View source for KAVAN Savage Mini - Instruction manual/en

<languages/>
=== Introduction ===
Congratulations on your purchase of the high-performance 3D aerobatic '''Savage Mini''' model. You are about to start the assembly of a model manufactured from virtually unbreakable EPP (extruded polypropylene) foam powered by a mighty brushless motor and lightweight LiPo battery. Everybody who has already mastered flying a "full house" trainer - with aileron, elevator, rudder, and throttle control - will enjoy this bad boy.

{{Image frame|width=900|content=[[File:KAVAN Savage Mini - blue.png|300px|KAV02.8027 KAVAN Savage Mini - blue]]|align=center|pos=bot|caption=<br>[https://kavanrc.com/item/kavan-savage-mini-blue-149280 '''KAV02.8027'''] '''KAVAN Savage Mini - {{font color | #0072B6 | blue }}'''}}

=== Before you start ===

# If you are not an experienced RC pilot, plan to have a fully competent pilot check your completed model and help you with your first flights. Even though we have tried to provide you with a thorough instruction manual, RC models are rather complicated and an experienced modeller can quickly check over your model to make sure your first flights are successful.
# Please assemble your model exactly according to these instructions. Do not attempt to modify or change your model in any way as doing so may adversely change its flying characteristics.
# Before you begin, please check the entire contents of this kit to make sure that no parts are missing or damaged. This will also help you to become familiar with each component of your plane. If you find that any of the parts are either missing or damaged, please contact your dealer immediately for replacement.
# Trial fit each part before glueing it in place. Make sure you are using the correct part and that it fits well before assembling. No amount of glue can make up for a poorly fitting part.
# The manual contains a drawing showing the default position of the Centre of Gravity (CG) and recommended control surface throws. Please note it is essential to keep the recommended CG position for the first flight otherwise the model could be unstable, hard to control or even unable to fly at all! Later you can fine-tune the CG position to suit your flying style and skills.

{{Note|type=info|text='''Note:''' Your dealer cannot accept kits for return if construction has begun.}}

=== Precautions ===
'''This RC model is not a toy.''' '''Use it with care and strictly following the instructions in this manual.'''

Assemble this model following strictly these instructions. DO NOT modify or alter the model. Failure to do so, the warranty will lapse automatically. Follow the instructions in order to obtain a safe and solid model at the end of the assembly.

Children under the age of 14 must operate the model under the supervision of an adult.

Assure that the model is in perfect condition before every flight, taking care that all the equipment works correctly and that the model is undamaged in its structure.

Fly only on days with a light breeze and in a safe place away from any obstacles.

=== Safety precautions and warnings ===

* An RC aeroplane is not a toy! If misused, it can cause serious bodily harm and damage to property. Fly only in a safe place following all instructions and recommendations in this manual. Beware of the propeller! Keep loose items that can get entangled in the propeller away from the spinning propeller, including loose clothing, or other objects such as pencils and screwdrivers. Ensure that your and other people’s hands and faces are kept away from the rotating propeller.
* As the user of this product, you are solely responsible for operating it in a manner that does not endanger yourself and others or result in damage to the product or the property of others. This model is controlled by a radio signal, that is subject to interference from many sources outside your control. This interference can cause momentary loss of control, so it is advisable to always keep a safe distance in all directions around your model, as this margin will help to avoid collisions or injury.
* Never operate your model with low transmitter batteries.
* Always operate your model in an open area away from power lines, cars, traffic, or people. Avoid operating your model in populated areas where injury or damage can occur.
* Carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable batteries, etc.) which you use.
* Keep all chemicals, small parts and anything electrical out of the reach of children.
* Moisture causes damage to electronics. Avoid water exposure to all equipment not specifically designed and protected for this purpose.
* The model is mostly made of plastics – it is not fireproof. It may not be exposed to higher temperatures, otherwise severe distortion of the foam airframe or other damage may occur.

=== Specification ===
{| class="wikitable" style="text-align: center; width: 100%;"
|+
|'''Wingspan'''
|1000 mm
|-
|'''Length'''
|1020 mm
|-
|'''All–up weight'''
|ca 500 g
|}

=== You will also need ===

* At least four channel RC set, a power unit with 3S LiPo flight pack and servos - refer to "Recommended power systems and servos".
* Regular modeller’s tools: modeller’s knife ([https://www.kavanrc.com/item/kavan-knife-with-cutting-mat-156305 KAV66.770]), screwdrivers, pliers, electric drill with drill bits (3.0 mm), No. 180–360 sandpaper, etc.
* Glue: medium ([https://www.kavanrc.com/item/kavan-power-ca-20g-medium-en-152585 KAV56.9952]) and thin ([https://www.kavanrc.com/item/kavan-power-ca-20g-thin-en-152583 KAV56.9951]) CA glue, accelerator for CA glue ([https://www.kavanrc.com/en/item/kavan-ca-activator-spray-150ml-152569 KAV56.9958] / [https://www.kavanrc.com/item/kavan-ca-activator-spray-200ml-152570 KAV56.9959]), hot melt glue.

=== Recommended power systems and servos ===

* Sunday 3D: For 3D aerobatic beginners and Sunday flyers.
* 3D: For everybody who likes it hot and 3D.
{{Note|type=info|text='''Note:''' 20–30A ESC with a good linear BEC should be OK if you are using analogue servos. However, if you are using high torque & speed digital servos, you should go for an ESC featuring powerful switching SBEC.}}
{| class="wikitable" style="text-align: center; width: 100%;"
|+
!
!Sunday 3D
!3D
|-
|Motor
|[https://www.kavanrc.com/item/kavan-brushless-motor-c2830-1300-140798 KAVAN C2830–1300]
|[https://www.kavanrc.com/item/kavan-brushless-motor-c2830-1300-140798 KAVAN PRO 2830–1300]
|-
|Propeller
|APC 9×4.7"SF
|APC 10×4.7"SF
|-
|ESC
|[https://kavanrc.com/item/kavan-r-30sb-plus-brushless-esc-sbec-30a-160597 KAVAN R-30SB Plus]
|[https://www.kavanrc.com/item/kavan-pro-30sb-brushless-esc-30a-140843 KAVAN PRO–30SB]
|-
|Battery
|[https://www.kavanrc.com/item/kavan-li-po-1300mah-11-1v-40-80c-14-4wh-140749 KAVAN LiPo 11.1V 1300mAh<br> 40/80C]
|[https://www.kavanrc.com/item/kavan-li-po-1300mah-11-1v-40-80c-14-4wh-140749 KAVAN LiPo 11.1V 1300mAh<br> 40/80C]
|-
|Servos
|[https://www.kavanrc.com/item/go-13mg-servo-13g-0-12s-60-2-8kg-cm-140701 KAVAN GO–13MG], Hitec HS-<br> -65MG, HS–70MG
|[https://www.kavanrc.com/item/go-1013mg-0-13s-60-3-8kg-cm-144745 KAVAN GO–1013MG], Hitec<br> HS–5065MG, HS–5070MH
|}

=== Assembly ===
Please follow the illustrated, step-by-step building manual below.

=== RC set installation and preflight check ===

* Referring to the instruction manual of your radio carefully hook up the onboard electronics. Correct linkage length - please refer to assembly steps 24, 50 and 60.
* Once everything has been correctly connected, turn on your transmitter and plug in the flight pack. Check the neutral positions and throws of all control surfaces. If you need to make the control surface throws smaller, simply move the pushrod closer to the centre on the servo arm or move it far from the control surface on the control horn. And vice versa.

{| class="wikitable" style="text-align: center; width: 100%;"
! rowspan="2" |'''Recommended throws'''
! colspan="2" |'''Low rate'''
! colspan="2" |'''High rate'''
|-
!Rate
!Expo
!Rate
!Expo
|-
|Ailerons
|± 30°
|45 %
|± 44° or more
|40 %
|-
|Elevator
|± 30°
|45 %
|± 50–60°
|45 %
|-
|Rudder
|± 35°
|50 %
|± 47°
|50 %
|}

* The "Low rate" recommended control surface throws are suitable for a less skilled pilot and classic pattern aerobatics. The "High rate" setting is for 3D aerobatics and skilled pilots.
* Check the direction of rotation of the propeller. If it was incorrect, simply swap two of the three wires between the ESC and motor or program the ESC (refer to the ESC manual).
* Attach the flight pack to the side of the bottom part of the fuselage using a strip of hook-and-loop tape to get the correct position of the centre of gravity (CG) 230 mm, refer to Fig. 63. You can fine-tune the CG position later in order to suit your flying style.
* Fully charge your flight pack and transmitter batteries, check the proper function of your radio and perform the range check of your radio according to its instruction manual. The range has to be almost the same with the motor off and at full throttle (no more than a 10% decrease is acceptable). DO NOT try to fly unless the range check is 100% successful.

=== Flying ===
The test flying and fine-tuning is pretty much straightforward. There will be no surprise for a medium-advanced pilot who is supposed to fly this model.

=== Parts list ===
If in doubt, the "Step No." will help you identify the part.
{| class="wikitable" style="text-align: center; width: 100%;"
|+
!'''Part'''
!'''Qty'''
!'''Material'''
!'''Dimensions'''
!'''Step No.'''
|-
|Instruction manual
|1
|paper
|A4
| -
|-
|Fuselage - vertical part
|1
|EPP
| -
|28
|-
|Fuselage - horizontal part
|1
|EPP
| -
|1
|-
|Wing - left + right
|1+1
|EPP
| -
|2
|-
|Canopy
|1
|EPP
| -
|28
|-
|Fin and rudder
|1
|EPP
| -
|56
|-
|Horizontal stabilizer + elevator
|1
|EPP
| -
|9
|-
|Wheel pant
|2+2
|EPP
| -
|41
|-
|Side force generator
|2
|EPP
| -
|61
|-
|Main undercarriage
|1
|carbon
| -
|32
|}
{| class="wikitable" style="text-align: center; width: 100%;"
!'''Carbon parts bundle'''
!'''Qty'''
!'''Material'''
!'''Dimensions'''
!'''Step No.'''
|-
|Wing spar
|2
|carbon
|Ø 1.5×1000 mm
|6
|-
|Fuselage reinforcement
|4
|carbon
|3×0.5×1000 mm
|12
|-
|Horizontal tailplane reinforcement
|2
|carbon
|3×0.5×250 mm
|9, 10
|-
|Horizontal tailplane reinforcement
|1
|carbon
|3×1×250 mm
|9
|-
|Elevator + rudder push rod
|1
|carbon
|Ø 1.0×1000 mm
|46, 50, 60
|}
{| class="wikitable" style="text-align: center; width: 100%;"
!'''Small accessories bag'''
!'''Qty'''
!'''Material'''
!'''Dimensions'''
!'''Step No.'''
|-
|Firewall
|1
|plywood
|3 mm
|53
|-
|Wing joiner
|1
|plywood
|1 mm
|7
|-
|Aileron push rod
|2
| -
|Ø 1.8×110 mm
|23
|-
|Aileron, elevator, rudder horns
|1 set
|plastic
| -
|21, 45, 57
|-
|Tailskid
|1
|plastic
| -
| -
|-
|Undercarriage plate
|1
|plastic
| -
|15
|-
|Wheel
|2
|plastic
|Ø 40 mm
|36
|-
|Wheel pant holder
|2
|plastic
|M3×16 mm socket screw
|36
|-
|Wheel axle
|2
|steel
|M3
|36
|-
|M3 nut
|4
|steel
|M3×25 mm socket screw
|36
|-
|M3 washer
|4
|steel
| -
|36
|-
|Undercarriage bolt
|4
|steel
| -
|35
|-
|Undercarriage bolt holder
|2
|plastic
| -
|31
|-
|Undercarriage bracket
|2
|plastic
| -
|32
|-
|Clevis
|7
|plastic
| -
|23, 46, 59
|-
|Clevis pin
|7
|brass
| -
|23, 46, 59
|-
|M2 ball link
|1
|plastic/brass
| -
|51
|}
{| class="wikitable" style="text-align: center; width: 100%;"
!'''Part'''
!'''Qty'''
!'''Material'''
!'''Dimensions'''
!'''Step No.'''
|-
|M2/1 threaded coupler
|2
|brass
| -
|48, 51
|-
|M2/2 threaded coupler
|2
|brass
| -
|23
|-
|Clevis spacer
|2
|plastic
|Ø 2 mm
|46
|-
|Push rod guide
|10
|plastic
| -
|43
|-
|Aileron servo arm
|2
|plastic
| -
|16
|-
|Motor mount screw
|4
|steel
|Ø 2.9×6 mm
|62
|}

=== Assembly ===
Follow the illustrated, step-by-step building manual below.

<p style="flex-wrap: wrap;display: flex;gap: 1em;justify-content: flex-start;">
[[File:SAVAGE MINI - Step 00a.png|border|450px]]
[[File:SAVAGE MINI - Step 00b.png|border|450px]]
[[File:SAVAGE MINI - Step 01.png|border|450px]]
[[File:SAVAGE MINI - Step 02.png|border|450px]]
[[File:SAVAGE MINI - Step 03.png|border|450px]]
[[File:SAVAGE MINI - Step 04.png|border|450px]]
[[File:SAVAGE MINI - Step 05.png|border|450px]]
[[File:SAVAGE MINI - Step 06.png|border|450px]]
[[File:SAVAGE MINI - Step 07.png|border|450px]]
[[File:SAVAGE MINI - Step 08.png|border|450px]]
[[File:SAVAGE MINI - Step 09.png|border|450px]]
[[File:SAVAGE MINI - Step 10.png|border|450px]]
[[File:SAVAGE MINI - Step 11.png|border|450px]]
[[File:SAVAGE MINI - Step 12.png|border|450px]]
[[File:SAVAGE MINI - Step 13.png|border|450px]]
[[File:SAVAGE MINI - Step 14.png|border|450px]]
[[File:SAVAGE MINI - Step 15.png|border|450px]]
[[File:SAVAGE MINI - Step 16.png|border|450px]]
[[File:SAVAGE MINI - Step 17.png|border|450px]]
[[File:SAVAGE MINI - Step 18.png|border|450px]]
[[File:SAVAGE MINI - Step 19.png|border|450px]]
[[File:SAVAGE MINI - Step 20.png|border|450px]]
[[File:SAVAGE MINI - Step 21.png|border|450px]]
[[File:SAVAGE MINI - Step 22.png|border|450px]]
[[File:SAVAGE MINI - Step 23.png|border|450px]]
[[File:SAVAGE MINI - Step 24.png|border|450px]]
[[File:SAVAGE MINI - Step 25.png|border|450px]]
[[File:SAVAGE MINI - Step 26.png|border|450px]]
[[File:SAVAGE MINI - Step 27.png|border|450px]]
[[File:SAVAGE MINI - Step 28.png|border|450px]]
[[File:SAVAGE MINI - Step 29.png|border|450px]]
[[File:SAVAGE MINI - Step 30.png|border|450px]]
[[File:SAVAGE MINI - Step 31.png|border|450px]]
[[File:SAVAGE MINI - Step 32.png|border|450px]]
[[File:SAVAGE MINI - Step 33.png|border|450px]]
[[File:SAVAGE MINI - Step 34.png|border|450px]]
[[File:SAVAGE MINI - Step 35.png|border|450px]]
[[File:SAVAGE MINI - Step 36.png|border|450px]]
[[File:SAVAGE MINI - Step 37.png|border|450px]]
[[File:SAVAGE MINI - Step 38.png|border|450px]]
[[File:SAVAGE MINI - Step 39.png|border|450px]]
[[File:SAVAGE MINI - Step 40.png|border|450px]]
[[File:SAVAGE MINI - Step 41.png|border|450px]]
[[File:SAVAGE MINI - Step 42.png|border|450px]]
[[File:SAVAGE MINI - Step 43.png|border|450px]]
[[File:SAVAGE MINI - Step 44.png|border|450px]]
[[File:SAVAGE MINI - Step 45.png|border|450px]]
[[File:SAVAGE MINI - Step 46.png|border|450px]]
[[File:SAVAGE MINI - Step 47.png|border|450px]]
[[File:SAVAGE MINI - Step 48.png|border|450px]]
[[File:SAVAGE MINI - Step 49.png|border|450px]]
[[File:SAVAGE MINI - Step 50.png|border|450px]]
[[File:SAVAGE MINI - Step 51.png|border|450px]]
[[File:SAVAGE MINI - Step 52.png|border|450px]]
[[File:SAVAGE MINI - Step 53.png|border|450px]]
[[File:SAVAGE MINI - Step 54.png|border|450px]]
[[File:SAVAGE MINI - Step 55.png|border|450px]]
[[File:SAVAGE MINI - Step 56.png|border|450px]]
[[File:SAVAGE MINI - Step 57.png|border|450px]]
[[File:SAVAGE MINI - Step 58.png|border|450px]]
[[File:SAVAGE MINI - Step 59.png|border|450px]]
[[File:SAVAGE MINI - Step 60.png|border|450px]]
[[File:SAVAGE MINI - Step 61.png|border|450px]]
[[File:SAVAGE MINI - Step 62.png|border|450px]]
[[File:SAVAGE MINI - Step 63.png|border|815px]]
</p>

===Guarantee===
The KAVAN Europe s.r.o. products are covered by a guarantee that fulfils currently valid legal requirements in your country. If you wish to make a claim under a guarantee, please contact the retailer from whom you first purchased the equipment. The guarantee does not cover faults caused in the following ways: crashes, improper use, incorrect connection, reversed polarity, maintenance work carried out late, incorrectly or not at all, or by unauthorised personnel, use of other than genuine KAVAN Europe s.r.o. accessories, modifications or repairs which were not carried out by KAVAN Europe s.r.o. or an authorised KAVAN Europe s.r.o., accidental or deliberate damage, defects caused by normal wear and tear, operation outside the Specification, or in conjunction with equipment made by other manufacturers.
Please be sure to read the appropriate information sheets in the product documentation!

If you have any questions about the SAVAGE Mini and its operation, please contact the technical and service staff at KAVAN Europe s.r.o. by e-mail ('''info@kavanrc.com''' for general technical information, '''service@kavanrc.com''' for service) or by phone ('''+420 466 260 133''' for general technical information, '''+420 463 358 700''' for service), during working hours 8:00 AM–4:00 PM CET, Monday to Friday).