KAVAN V15 - Changing the mode - Revision history

Mr. KAVAN: /* Video tutorial */

2026-05-06T07:45:00Z

Video tutorial

← Older revision		Revision as of 09:45, 6 May 2026
Line 53:		Line 53:
	<!--T:3-->		<!--T:3-->
	=== Video tutorial ===		=== Video tutorial ===
	If you need a more detailed ~~tutorial~~, watch this video tutorial, where you can find all the moves described above step by step.		If you need a more detailed guide, watch this video tutorial, where you can find all the moves described above step by step.
	<div class="videoWrapper"><html><iframe class="videoW" src="https://www.youtube.com/embed/2M8KZyQxJnI?si=3VKIxEBH7wC1gLyM"		<div class="videoWrapper"><html><iframe class="videoW" src="https://www.youtube.com/embed/2M8KZyQxJnI?si=3VKIxEBH7wC1gLyM"
	title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" referrerpolicy="strict-origin-when-cross-origin" allowfullscreen></iframe></html></div>		title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" referrerpolicy="strict-origin-when-cross-origin" allowfullscreen></iframe></html></div>
	</translate>		</translate>

Mrs. Kavan: Marked this version for translation

2025-12-19T08:42:16Z

Marked this version for translation

← Older revision		Revision as of 10:42, 19 December 2025
Line 2:		Line 2:
	<translate>		<translate>

			<!--T:1-->
	=== Introduction ===		=== Introduction ===
	This brief guide walks you through the procedure, which takes just a few minutes to complete. Be careful manipulating the split shell. Pay extra attention to not damage the antennas. Tighten the tension and ratcheting strip screws so the movement resistance of the sticks matches your preference.		This brief guide walks you through the procedure, which takes just a few minutes to complete. Be careful manipulating the split shell. Pay extra attention to not damage the antennas. Tighten the tension and ratcheting strip screws so the movement resistance of the sticks matches your preference.

			<!--T:2-->
	=== Steps ===		=== Steps ===
	{\| class="wikitable" style="text-align: center; width: 100%;"		{\| class="wikitable" style="text-align: center; width: 100%;"
Line 49:		Line 51:
	'''Congratulations. The mode is now changed.'''		'''Congratulations. The mode is now changed.'''

			<!--T:3-->
	=== Video tutorial ===		=== Video tutorial ===
	If you need a more detailed tutorial, watch this video tutorial, where you can find all the moves described above step by step.		If you need a more detailed tutorial, watch this video tutorial, where you can find all the moves described above step by step.

Mrs. Kavan at 08:42, 19 December 2025

2025-12-19T08:42:08Z

← Older revision		Revision as of 10:42, 19 December 2025
Line 1:		Line 1:
			<languages/>
			<translate>

	=== Introduction ===		=== Introduction ===
	This brief guide walks you through the procedure, which takes just a few minutes to complete. Be careful manipulating the split shell. Pay extra attention to not damage the antennas. Tighten the tension and ratcheting strip screws so the movement resistance of the sticks matches your preference.		This brief guide walks you through the procedure, which takes just a few minutes to complete. Be careful manipulating the split shell. Pay extra attention to not damage the antennas. Tighten the tension and ratcheting strip screws so the movement resistance of the sticks matches your preference.
Line 4:		Line 7:
	=== Steps ===		=== Steps ===
	{\| class="wikitable" style="text-align: center; width: 100%;"		{\| class="wikitable" style="text-align: center; width: 100%;"
	!Step 1		!Step 1
	\|First, remove the battery tray cover and unplug the battery. Then, unscrew the four screws on the rear shell and slowly begin to remove it, starting from the bottom side. Be careful not to break the two plastic pins behind the display.		\|First, remove the battery tray cover and unplug the battery. Then, unscrew the four screws on the rear shell and slowly begin to remove it, starting from the bottom side. Be careful not to break the two plastic pins behind the display.
	\|[[File:V15 Mode change Step 1.png\|frameless\|300x300px]]		\|[[File:V15 Mode change Step 1.png\|frameless\|300x300px]]
	\|-		\|-
	!Step 2		!Step 2
	\|Remove the side rotary sliders and place them into the mounts on the front shell so they don’t get in the way during the replacement. Unplug the flex cable by unlocking it upwards/towards you.		\|Remove the side rotary sliders and place them into the mounts on the front shell so they don’t get in the way during the replacement. Unplug the flex cable by unlocking it upwards/towards you.
	\|[[File:V15 Mode change Step 2.png\|frameless\|300x300px]]		\|[[File:V15 Mode change Step 2.png\|frameless\|300x300px]]
	\|-		\|-
	!Step 3		!Step 3
	\|Unscrew the self-centring spring lock from the current throttle stick. Lifting the spring arm upwards makes the process easier.		\|Unscrew the self-centring spring lock from the current throttle stick. Lifting the spring arm upwards makes the process easier.
	\|[[File:V15 Mode change Step 3.png\|frameless\|300x300px]]		\|[[File:V15 Mode change Step 3.png\|frameless\|300x300px]]
	\|-		\|-
	!Step 4		!Step 4
	\|Now loosen the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the more you loosen it, the easier it is to move the stick), then check that the gimbal can move freely in all directions.		\|Now loosen the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the more you loosen it, the easier it is to move the stick), then check that the gimbal can move freely in all directions.
	\|[[File:V15 Mode change Step 4.png\|frameless\|300x300px]]		\|[[File:V15 Mode change Step 4.png\|frameless\|300x300px]]
	\|-		\|-
	!Step 5		!Step 5
	\|Insert and screw in the self-centring spring lock into the other gimbal. Again, lifting the spring arm will help you. On the same stick, loosen the self-centring spring screw (the less it is tightened, the weaker the centring force is).		\|Insert and screw in the self-centring spring lock into the other gimbal. Again, lifting the spring arm will help you. On the same stick, loosen the self-centring spring screw (the less it is tightened, the weaker the centring force is).
	\|[[File:V15 Mode change Step 5.png\|frameless\|300x300px]]		\|[[File:V15 Mode change Step 5.png\|frameless\|300x300px]]
	\|-		\|-
	!Step 6		!Step 6
	\|Adjust the screws on the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the tighter it is, the more force is needed to move the stick). Tighten the self-centring spring screw on the opposite side to centre the stick.		\|Adjust the screws on the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the tighter it is, the more force is needed to move the stick). Tighten the self-centring spring screw on the opposite side to centre the stick.
	\|[[File:V15 Mode change Step 6.png\|frameless\|300x300px]]		\|[[File:V15 Mode change Step 6.png\|frameless\|300x300px]]
	\|-		\|-
	!Step 7		!Step 7
	\|Check that both gimbals can move freely and that the tension and ratcheting feel right to you; if not, go back one step and loosen or tighten the screws of the ratcheting and tension strip as needed.		\|Check that both gimbals can move freely and that the tension and ratcheting feel right to you; if not, go back one step and loosen or tighten the screws of the ratcheting and tension strip as needed.
	\|[[File:V15 Mode change Step 7.png\|frameless\|300x300px]]		\|[[File:V15 Mode change Step 7.png\|frameless\|300x300px]]
	\|-		\|-
	!Step 8		!Step 8
	\|Plug the flex cable back in and make sure it is properly locked by “clicking” it into place. The flex cable must be connected straight, so adjust the connection carefully if necessary.		\|Plug the flex cable back in and make sure it is properly locked by “clicking” it into place. The flex cable must be connected straight, so adjust the connection carefully if necessary.
	\|[[File:V15 Mode change Step 8.png\|frameless\|300x300px]]		\|[[File:V15 Mode change Step 8.png\|frameless\|300x300px]]
	\|-		\|-
	!Step 9		!Step 9
	\|Carefully pop the rear shell back in – keep in mind that the connectors must be properly centred. After checking that everything fits correctly, screw in the four screws on the rear shell. Then plug the battery back in and close the battery case cover.		\|Carefully pop the rear shell back in – keep in mind that the connectors must be properly centred. After checking that everything fits correctly, screw in the four screws on the rear shell. Then plug the battery back in and close the battery case cover.
	\|[[File:V15 Mode change Step 9.png\|frameless\|300x300px]]		\|[[File:V15 Mode change Step 9.png\|frameless\|300x300px]]
	\|-		\|-
	!Step 10		!Step 10
	\|Turn on the transmitter. Go to the “System” menu and open the “Sticks” menu. Change the stick mode – in this case, from “Mode 2” to “Mode 1”. Check the operation of the channels in the “Outputs” in the “Model” menu.		\|Turn on the transmitter. Go to the “System” menu and open the “Sticks” menu. Change the stick mode – in this case, from “Mode 2” to “Mode 1”. Check the operation of the channels in the “Outputs” in the “Model” menu.
	\|[[File:V15 Mode change Step 10.png\|frameless\|300x300px]]		\|[[File:V15 Mode change Step 10.png\|frameless\|300x300px]]
Line 50:		Line 53:
	<div class="videoWrapper"><html><iframe class="videoW" src="https://www.youtube.com/embed/2M8KZyQxJnI?si=3VKIxEBH7wC1gLyM"		<div class="videoWrapper"><html><iframe class="videoW" src="https://www.youtube.com/embed/2M8KZyQxJnI?si=3VKIxEBH7wC1gLyM"
	title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" referrerpolicy="strict-origin-when-cross-origin" allowfullscreen></iframe></html></div>		title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" referrerpolicy="strict-origin-when-cross-origin" allowfullscreen></iframe></html></div>
			</translate>

Mrs. Kavan at 08:39, 19 December 2025

2025-12-19T08:39:10Z

← Older revision		Revision as of 10:39, 19 December 2025
Line 3:		Line 3:

	=== Steps ===		=== Steps ===
	~~<ol~~ style="~~list~~-~~style-type~~:~~decimal~~">		{\| class="wikitable" style="text-align: center; width: 100%;"
	~~<li>~~ First, remove the battery tray cover and unplug the battery. Then, unscrew the four screws on the rear shell and slowly begin to remove it, starting from the bottom side. Be careful not to break the two plastic pins behind the display.~~<br>~~		!Step 1
	[[File:V15 Mode change Step 1.png\|frameless\|300x300px]]~~</li>~~		\|First, remove the battery tray cover and unplug the battery. Then, unscrew the four screws on the rear shell and slowly begin to remove it, starting from the bottom side. Be careful not to break the two plastic pins behind the display.
	~~<li>~~ Remove the side rotary sliders and place them into the mounts on the front shell so they don’t get in the way during the replacement. Unplug the flex cable by unlocking it upwards/towards you.~~<br>~~		\|[[File:V15 Mode change Step 1.png\|frameless\|300x300px]]
	[[File:V15 Mode change Step 2.png\|frameless\|300x300px]]~~</li>~~		\|-
	~~<li>~~Unscrew the self-centring spring lock from the current throttle stick. Lifting the spring arm upwards makes the process easier.~~<br>~~		!Step 2
	[[File:V15 Mode change Step 3.png\|frameless\|300x300px]]~~</li>~~		\|Remove the side rotary sliders and place them into the mounts on the front shell so they don’t get in the way during the replacement. Unplug the flex cable by unlocking it upwards/towards you.
	~~<li>~~Now loosen the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the more you loosen it, the easier it is to move the stick), then check that the gimbal can move freely in all directions.~~<br>~~		\|[[File:V15 Mode change Step 2.png\|frameless\|300x300px]]
	[[File:V15 Mode change Step 4.png\|frameless\|300x300px]]~~</li>~~		\|-
	~~<li>~~Insert and screw in the self-centring spring lock into the other gimbal. Again, lifting the spring arm will help you. On the same stick, loosen the self-centring spring screw (the less it is tightened, the weaker the centring force is).~~<br>~~		!Step 3
	[[File:V15 Mode change Step 5.png\|frameless\|300x300px]]~~</li>~~		\|Unscrew the self-centring spring lock from the current throttle stick. Lifting the spring arm upwards makes the process easier.
	~~<li>~~Adjust the screws on the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the tighter it is, the more force is needed to move the stick). Tighten the self-centring spring screw on the opposite side to centre the stick.~~<br>~~		\|[[File:V15 Mode change Step 3.png\|frameless\|300x300px]]
	[[File:V15 Mode change Step 6.png\|frameless\|300x300px]]~~</li>~~		\|-
	~~<li>~~Check that both gimbals can move freely and that the tension and ratcheting feel right to you; if not, go back one step and loosen or tighten the screws of the ratcheting and tension strip as needed.~~<br>~~		!Step 4
	[[File:V15 Mode change Step 7.png\|frameless\|300x300px]]~~</li>~~		\|Now loosen the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the more you loosen it, the easier it is to move the stick), then check that the gimbal can move freely in all directions.
	~~<li>~~Plug the flex cable back in and make sure it is properly locked by “clicking” it into place. The flex cable must be connected straight, so adjust the connection carefully if necessary.~~<br>~~		\|[[File:V15 Mode change Step 4.png\|frameless\|300x300px]]
	[[File:V15 Mode change Step 8.png\|frameless\|300x300px]]~~</li>~~		\|-
	~~<li>~~Carefully pop the rear shell back in – keep in mind that the connectors must be properly centred. After checking that everything fits correctly, screw in the four screws on the rear shell. Then plug the battery back in and close the battery case cover.~~<br>~~		!Step 5
	[[File:V15 Mode change Step 9.png\|frameless\|300x300px]]~~</li>~~		\|Insert and screw in the self-centring spring lock into the other gimbal. Again, lifting the spring arm will help you. On the same stick, loosen the self-centring spring screw (the less it is tightened, the weaker the centring force is).
	~~<li>~~Turn on the transmitter. Go to the “System” menu and open the “Sticks” menu. Change the stick mode – in this case, from “Mode 2” to “Mode 1”. Check the operation of the channels in the “Outputs” in the “Model” menu.~~<br>~~		\|[[File:V15 Mode change Step 5.png\|frameless\|300x300px]]
	[[File:V15 Mode change Step 10.png\|frameless\|300x300px]]~~</li></ol>~~		\|-
			!Step 6
			\|Adjust the screws on the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the tighter it is, the more force is needed to move the stick). Tighten the self-centring spring screw on the opposite side to centre the stick.
			\|[[File:V15 Mode change Step 6.png\|frameless\|300x300px]]
			\|-
			!Step 7
			\|Check that both gimbals can move freely and that the tension and ratcheting feel right to you; if not, go back one step and loosen or tighten the screws of the ratcheting and tension strip as needed.
			\|[[File:V15 Mode change Step 7.png\|frameless\|300x300px]]
			\|-
			!Step 8
			\|Plug the flex cable back in and make sure it is properly locked by “clicking” it into place. The flex cable must be connected straight, so adjust the connection carefully if necessary.
			\|[[File:V15 Mode change Step 8.png\|frameless\|300x300px]]
			\|-
			!Step 9
			\|Carefully pop the rear shell back in – keep in mind that the connectors must be properly centred. After checking that everything fits correctly, screw in the four screws on the rear shell. Then plug the battery back in and close the battery case cover.
			\|[[File:V15 Mode change Step 9.png\|frameless\|300x300px]]
			\|-
			!Step 10
			\|Turn on the transmitter. Go to the “System” menu and open the “Sticks” menu. Change the stick mode – in this case, from “Mode 2” to “Mode 1”. Check the operation of the channels in the “Outputs” in the “Model” menu.
			\|[[File:V15 Mode change Step 10.png\|frameless\|300x300px]]
			\|}
	'''Congratulations. The mode is now changed.'''		'''Congratulations. The mode is now changed.'''

Mrs. Kavan at 14:58, 18 December 2025

2025-12-18T14:58:55Z

Mrs. Kavan at 14:56, 18 December 2025

2025-12-18T14:56:49Z

← Older revision		Revision as of 16:56, 18 December 2025
Line 3:		Line 3:

	=== Steps ===		=== Steps ===
	# First, remove the battery tray cover and unplug the battery. Then, unscrew the four screws on the rear shell and slowly begin to remove it, starting from the bottom side. Be careful not to break the two plastic pins behind the display.		<ol style="list-style-type:decimal">
	# Remove the side rotary sliders and place them into the mounts on the front shell so they don’t get in the way during the replacement. Unplug the flex cable by unlocking it upwards/towards you.		<li> First, remove the battery tray cover and unplug the battery. Then, unscrew the four screws on the rear shell and slowly begin to remove it, starting from the bottom side. Be careful not to break the two plastic pins behind the display.<br>
	# Unscrew the self-centring spring lock from the current throttle stick. Lifting the spring arm upwards makes the process easier.		[[File:V15 Mode change Step 1.png\|frameless\|250x250px]]</li>
	# Now loosen the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the more you loosen it, the easier it is to move the stick), then check that the gimbal can move freely in all directions.		<li> Remove the side rotary sliders and place them into the mounts on the front shell so they don’t get in the way during the replacement. Unplug the flex cable by unlocking it upwards/towards you.<br>
	# Insert and screw in the self-centring spring lock into the other gimbal. Again, lifting the spring arm will help you. On the same stick, loosen the self-centring spring screw (the less it is tightened, the weaker the centring force is).		[[File:V15 Mode change Step 2.png\|frameless\|250x250px]]</li>
	# Adjust the screws on the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the tighter it is, the more force is needed to move the stick). Tighten the self-centring spring screw on the opposite side to centre the stick.		<li>Unscrew the self-centring spring lock from the current throttle stick. Lifting the spring arm upwards makes the process easier.<br>
	# Check that both gimbals can move freely and that the tension and ratcheting feel right to you; if not, go back one step and loosen or tighten the screws of the ratcheting and tension strip as needed.		[[File:V15 Mode change Step 3.png\|frameless\|250x250px]]</li>
	# Plug the flex cable back in and make sure it is properly locked by “clicking” it into place. The flex cable must be connected straight, so adjust the connection carefully if necessary.		<li>Now loosen the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the more you loosen it, the easier it is to move the stick), then check that the gimbal can move freely in all directions.<br>
	# Carefully pop the rear shell back in – keep in mind that the connectors must be properly centred. After checking that everything fits correctly, screw in the four screws on the rear shell. Then plug the battery back in and close the battery case cover.		[[File:V15 Mode change Step 4.png\|frameless\|250x250px]]</li>
	# Turn on the transmitter. Go to the “System” menu and open the “Sticks” menu. Change the stick mode – in this case, from “Mode 2” to “Mode 1”. Check the operation of the channels in the “Outputs” in the “Model” menu.		<li>Insert and screw in the self-centring spring lock into the other gimbal. Again, lifting the spring arm will help you. On the same stick, loosen the self-centring spring screw (the less it is tightened, the weaker the centring force is).<br>
			[[File:V15 Mode change Step 5.png\|frameless\|250x250px]]</li>
			<li>Adjust the screws on the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the tighter it is, the more force is needed to move the stick). Tighten the self-centring spring screw on the opposite side to centre the stick.<br>
			[[File:V15 Mode change Step 6.png\|frameless\|250x250px]]</li>
			<li>Check that both gimbals can move freely and that the tension and ratcheting feel right to you; if not, go back one step and loosen or tighten the screws of the ratcheting and tension strip as needed.<br>
			[[File:V15 Mode change Step 7.png\|frameless\|250x250px]]</li>
			<li>Plug the flex cable back in and make sure it is properly locked by “clicking” it into place. The flex cable must be connected straight, so adjust the connection carefully if necessary.<br>
			[[File:V15 Mode change Step 8.png\|frameless\|250x250px]]</li>
			<li>Carefully pop the rear shell back in – keep in mind that the connectors must be properly centred. After checking that everything fits correctly, screw in the four screws on the rear shell. Then plug the battery back in and close the battery case cover.<br>
			[[File:V15 Mode change Step 9.png\|frameless\|250x250px]]</li>
			<li>Turn on the transmitter. Go to the “System” menu and open the “Sticks” menu. Change the stick mode – in this case, from “Mode 2” to “Mode 1”. Check the operation of the channels in the “Outputs” in the “Model” menu.<br>
			[[File:V15 Mode change Step 10.png\|frameless\|250x250px]]</li></ol>

	'''Congratulations. The mode is now changed.'''		'''Congratulations. The mode is now changed.'''

Mrs. Kavan at 14:19, 18 December 2025

2025-12-18T14:19:16Z

← Older revision		Revision as of 16:19, 18 December 2025
Line 13:		Line 13:
	# Carefully pop the rear shell back in – keep in mind that the connectors must be properly centred. After checking that everything fits correctly, screw in the four screws on the rear shell. Then plug the battery back in and close the battery case cover.		# Carefully pop the rear shell back in – keep in mind that the connectors must be properly centred. After checking that everything fits correctly, screw in the four screws on the rear shell. Then plug the battery back in and close the battery case cover.
	# Turn on the transmitter. Go to the “System” menu and open the “Sticks” menu. Change the stick mode – in this case, from “Mode 2” to “Mode 1”. Check the operation of the channels in the “Outputs” in the “Model” menu.		# Turn on the transmitter. Go to the “System” menu and open the “Sticks” menu. Change the stick mode – in this case, from “Mode 2” to “Mode 1”. Check the operation of the channels in the “Outputs” in the “Model” menu.
			'''Congratulations. The mode is now changed.'''

	=== Video tutorial ===		=== Video tutorial ===
	~~'''Congratulations. The mode is now changed.'''<br>~~
	If you need a more detailed tutorial, watch this video tutorial, where you can find all the moves described above step by step.		If you need a more detailed tutorial, watch this video tutorial, where you can find all the moves described above step by step.
	<div class="videoWrapper"><html><iframe class="videoW" src="https://www.youtube.com/embed/2M8KZyQxJnI?si=3VKIxEBH7wC1gLyM"		<div class="videoWrapper"><html><iframe class="videoW" src="https://www.youtube.com/embed/2M8KZyQxJnI?si=3VKIxEBH7wC1gLyM"
	title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" referrerpolicy="strict-origin-when-cross-origin" allowfullscreen></iframe></html></div>		title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" referrerpolicy="strict-origin-when-cross-origin" allowfullscreen></iframe></html></div>

Mrs. Kavan at 14:11, 18 December 2025

2025-12-18T14:11:36Z

← Older revision		Revision as of 16:11, 18 December 2025
Line 17:		Line 17:
	'''Congratulations. The mode is now changed.'''<br>		'''Congratulations. The mode is now changed.'''<br>
	If you need a more detailed tutorial, watch this video tutorial, where you can find all the moves described above step by step.		If you need a more detailed tutorial, watch this video tutorial, where you can find all the moves described above step by step.
	<div class="videoWrapper"><html><iframe class="videoW" src="https://~~youtu~~.be/2M8KZyQxJnI?si=~~4euQ5KB7ev8qQoxm~~" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" referrerpolicy="strict-origin-when-cross-origin" allowfullscreen></iframe></html></div>		<div class="videoWrapper"><html><iframe class="videoW" src="https://www.youtube.com/embed/2M8KZyQxJnI?si=3VKIxEBH7wC1gLyM"
			title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" referrerpolicy="strict-origin-when-cross-origin" allowfullscreen></iframe></html></div>

Mrs. Kavan: Created page with "=== Introduction === This brief guide walks you through the procedure, which takes just a few minutes to complete. Be careful manipulating the split shell. Pay extra attention to not damage the antennas. Tighten the tension and ratcheting strip screws so the movement resistance of the sticks matches your preference. === Steps === # First, remove the battery tray cover and unplug the battery. Then, unscrew the four screws on the rear shell and slowly begin to remove it,..."

2025-12-18T14:07:40Z

Created page with "=== Introduction === This brief guide walks you through the procedure, which takes just a few minutes to complete. Be careful manipulating the split shell. Pay extra attention to not damage the antennas. Tighten the tension and ratcheting strip screws so the movement resistance of the sticks matches your preference. === Steps === # First, remove the battery tray cover and unplug the battery. Then, unscrew the four screws on the rear shell and slowly begin to remove it,..."

New page

=== Introduction ===
This brief guide walks you through the procedure, which takes just a few minutes to complete. Be careful manipulating the split shell. Pay extra attention to not damage the antennas. Tighten the tension and ratcheting strip screws so the movement resistance of the sticks matches your preference.

=== Steps ===
# First, remove the battery tray cover and unplug the battery. Then, unscrew the four screws on the rear shell and slowly begin to remove it, starting from the bottom side. Be careful not to break the two plastic pins behind the display.
# Remove the side rotary sliders and place them into the mounts on the front shell so they don’t get in the way during the replacement. Unplug the flex cable by unlocking it upwards/towards you.
# Unscrew the self-centring spring lock from the current throttle stick. Lifting the spring arm upwards makes the process easier.
# Now loosen the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the more you loosen it, the easier it is to move the stick), then check that the gimbal can move freely in all directions.
# Insert and screw in the self-centring spring lock into the other gimbal. Again, lifting the spring arm will help you. On the same stick, loosen the self-centring spring screw (the less it is tightened, the weaker the centring force is).
# Adjust the screws on the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the tighter it is, the more force is needed to move the stick). Tighten the self-centring spring screw on the opposite side to centre the stick.
# Check that both gimbals can move freely and that the tension and ratcheting feel right to you; if not, go back one step and loosen or tighten the screws of the ratcheting and tension strip as needed.
# Plug the flex cable back in and make sure it is properly locked by “clicking” it into place. The flex cable must be connected straight, so adjust the connection carefully if necessary.
# Carefully pop the rear shell back in – keep in mind that the connectors must be properly centred. After checking that everything fits correctly, screw in the four screws on the rear shell. Then plug the battery back in and close the battery case cover.
# Turn on the transmitter. Go to the “System” menu and open the “Sticks” menu. Change the stick mode – in this case, from “Mode 2” to “Mode 1”. Check the operation of the channels in the “Outputs” in the “Model” menu.

=== Video tutorial ===
'''Congratulations. The mode is now changed.'''<br>
If you need a more detailed tutorial, watch this video tutorial, where you can find all the moves described above step by step.
<div class="videoWrapper"><html><iframe class="videoW" src="https://youtu.be/2M8KZyQxJnI?si=4euQ5KB7ev8qQoxm" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" referrerpolicy="strict-origin-when-cross-origin" allowfullscreen></iframe></html></div>

← Older revision		Revision as of 16:58, 18 December 2025
Line 5:		Line 5:
	<ol style="list-style-type:decimal">		<ol style="list-style-type:decimal">
	<li> First, remove the battery tray cover and unplug the battery. Then, unscrew the four screws on the rear shell and slowly begin to remove it, starting from the bottom side. Be careful not to break the two plastic pins behind the display.<br>		<li> First, remove the battery tray cover and unplug the battery. Then, unscrew the four screws on the rear shell and slowly begin to remove it, starting from the bottom side. Be careful not to break the two plastic pins behind the display.<br>
	[[File:V15 Mode change Step 1.png\|frameless\|~~250x250px~~]]</li>		[[File:V15 Mode change Step 1.png\|frameless\|300x300px]]</li>
	<li> Remove the side rotary sliders and place them into the mounts on the front shell so they don’t get in the way during the replacement. Unplug the flex cable by unlocking it upwards/towards you.<br>		<li> Remove the side rotary sliders and place them into the mounts on the front shell so they don’t get in the way during the replacement. Unplug the flex cable by unlocking it upwards/towards you.<br>
	[[File:V15 Mode change Step 2.png\|frameless\|~~250x250px~~]]</li>		[[File:V15 Mode change Step 2.png\|frameless\|300x300px]]</li>
	<li>Unscrew the self-centring spring lock from the current throttle stick. Lifting the spring arm upwards makes the process easier.<br>		<li>Unscrew the self-centring spring lock from the current throttle stick. Lifting the spring arm upwards makes the process easier.<br>
	[[File:V15 Mode change Step 3.png\|frameless\|~~250x250px~~]]</li>		[[File:V15 Mode change Step 3.png\|frameless\|300x300px]]</li>
	<li>Now loosen the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the more you loosen it, the easier it is to move the stick), then check that the gimbal can move freely in all directions.<br>		<li>Now loosen the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the more you loosen it, the easier it is to move the stick), then check that the gimbal can move freely in all directions.<br>
	[[File:V15 Mode change Step 4.png\|frameless\|~~250x250px~~]]</li>		[[File:V15 Mode change Step 4.png\|frameless\|300x300px]]</li>
	<li>Insert and screw in the self-centring spring lock into the other gimbal. Again, lifting the spring arm will help you. On the same stick, loosen the self-centring spring screw (the less it is tightened, the weaker the centring force is).<br>		<li>Insert and screw in the self-centring spring lock into the other gimbal. Again, lifting the spring arm will help you. On the same stick, loosen the self-centring spring screw (the less it is tightened, the weaker the centring force is).<br>
	[[File:V15 Mode change Step 5.png\|frameless\|~~250x250px~~]]</li>		[[File:V15 Mode change Step 5.png\|frameless\|300x300px]]</li>
	<li>Adjust the screws on the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the tighter it is, the more force is needed to move the stick). Tighten the self-centring spring screw on the opposite side to centre the stick.<br>		<li>Adjust the screws on the ratcheting strip [1] (adjusts the ratchet strength) and the tension strip [2] (the tighter it is, the more force is needed to move the stick). Tighten the self-centring spring screw on the opposite side to centre the stick.<br>
	[[File:V15 Mode change Step 6.png\|frameless\|~~250x250px~~]]</li>		[[File:V15 Mode change Step 6.png\|frameless\|300x300px]]</li>
	<li>Check that both gimbals can move freely and that the tension and ratcheting feel right to you; if not, go back one step and loosen or tighten the screws of the ratcheting and tension strip as needed.<br>		<li>Check that both gimbals can move freely and that the tension and ratcheting feel right to you; if not, go back one step and loosen or tighten the screws of the ratcheting and tension strip as needed.<br>
	[[File:V15 Mode change Step 7.png\|frameless\|~~250x250px~~]]</li>		[[File:V15 Mode change Step 7.png\|frameless\|300x300px]]</li>
	<li>Plug the flex cable back in and make sure it is properly locked by “clicking” it into place. The flex cable must be connected straight, so adjust the connection carefully if necessary.<br>		<li>Plug the flex cable back in and make sure it is properly locked by “clicking” it into place. The flex cable must be connected straight, so adjust the connection carefully if necessary.<br>
	[[File:V15 Mode change Step 8.png\|frameless\|~~250x250px~~]]</li>		[[File:V15 Mode change Step 8.png\|frameless\|300x300px]]</li>
	<li>Carefully pop the rear shell back in – keep in mind that the connectors must be properly centred. After checking that everything fits correctly, screw in the four screws on the rear shell. Then plug the battery back in and close the battery case cover.<br>		<li>Carefully pop the rear shell back in – keep in mind that the connectors must be properly centred. After checking that everything fits correctly, screw in the four screws on the rear shell. Then plug the battery back in and close the battery case cover.<br>
	[[File:V15 Mode change Step 9.png\|frameless\|~~250x250px~~]]</li>		[[File:V15 Mode change Step 9.png\|frameless\|300x300px]]</li>
	<li>Turn on the transmitter. Go to the “System” menu and open the “Sticks” menu. Change the stick mode – in this case, from “Mode 2” to “Mode 1”. Check the operation of the channels in the “Outputs” in the “Model” menu.<br>		<li>Turn on the transmitter. Go to the “System” menu and open the “Sticks” menu. Change the stick mode – in this case, from “Mode 2” to “Mode 1”. Check the operation of the channels in the “Outputs” in the “Model” menu.<br>
	[[File:V15 Mode change Step 10.png\|frameless\|~~250x250px~~]]</li></ol>		[[File:V15 Mode change Step 10.png\|frameless\|300x300px]]</li></ol>

	'''Congratulations. The mode is now changed.'''		'''Congratulations. The mode is now changed.'''