FuzzyBot: FuzzyBot moved page Translations:Kavan AP06A - Instruction Manual/90/en to Translations:KAVAN AP06A - Instruction Manual/90/en without leaving a redirect: Part of translatable page "Kavan AP06A - Instruction Manual"

2025-10-15T09:24:08Z

FuzzyBot moved page Translations:Kavan AP06A - Instruction Manual/90/en to Translations:KAVAN AP06A - Instruction Manual/90/en without leaving a redirect: Part of translatable page "Kavan AP06A - Instruction Manual"

← Older revision		Revision as of 11:24, 15 October 2025
(No difference)

FuzzyBot: Importing a new version from external source

2025-08-06T05:26:14Z

Importing a new version from external source

New page

|'''PROBLEM'''
|'''CAUSE'''
|'''SOLUTION'''
|-
|rowspan="7"|1) Engine does not start
|A) Failed glow plug
|A) Replace glow plug with a new one
|-
|B) Glow Starter not charged and/or faulty
|B) Fully charge glow starter and/or replace
|-
|C) Engine not being turned over fast enough
|C) Use an electric starter to start engine
|-
|D) Old or contaminated fuel
|D) Replace with new fuel
|-
|E) Engine flooded with too much fuel
|E) Remove glow plug and expel fuel from cylinder
|-
|F) Faulty fuel tank and/or stopper assembly
|F) Check and/or replace fuel tank assembly
|-
|G) Air leak in fuel system and/or engine
|G) Replace fuel lines and/or tighten all engine bolts
|-
|rowspan="4"|2) Engine does not draw fuel
|A) Air leak in fuel system and/or engine
|A) Replace fuel lines and/or tighten all engine bolts
|-
|B) High Speed Needle Valve fully closed
|B) Reset high speed needle valve to factory setting
|-
|C) Fuel lines kinked
|C) Check and straighten fuel lines
|-
|D) Defective fuel tank
|D) Replace fuel tank
|-
|rowspan="2"|3) Engine vibrates excessively
|A) Propeller out of balance
|A) Balance propeller
|-
|B) Engine and/or motor mount loose
|B) Tighten motor mounting bolts
|-
|rowspan="5"|4) Engine does not transition
|A) Failed and/or wrong type glow plug
|A) Replace with new recommended glow plug
|-
|B) Old and/or wrong type fuel
|B) Replace with new recommended fuel
|-
|C) High speed needle valve set too rich
|C) Reset high speed needle valve to leaner setting
|-
|D) Air leak in fuel system and/or engine
|D) Replace fuel lines and/or tighten all engine bolts
|-
|E) Propeller too large
|E) Replace with one size smaller propeller
|-
|rowspan="2"|5) Throttle barrel does not close completely
|A) Idle stop screw out of adjustment
|A) Turn idle stop screw counter clockwise until barrel closes completely
|-
|B) Throttle servo linkage out of adjustment
|B) Adjust throttle linkage to close throttle barrel completely.
|-
|rowspan="4"|6) Engine Overheats
|A) Engine running too lean
|A) Richen high speed needle valve
|-
|B) Cowl too restrictive
|B) Open larger vents in cowling to allow air to exit
|-
|C) Wrong type of fuel used
|C) Use fuel with recommended oil content
|-
|D) Engine not fully broken-in
|D) Allow engine further break-in time
|-
|rowspan="3"|7) Engine stops abruptly
|A) Engine running too lean
|A) Richen high speed needle valve
|-
|B) Piston & Cylinder fit loose
|B) Return engine to KAVAN Engines Service Centre
|-
|C) Compression ratio too high
|C) Install one head gasket to lower compression
|}

Translations:KAVAN AP06A - Instruction Manual/90/en - Revision history

FuzzyBot: FuzzyBot moved page Translations:Kavan AP06A - Instruction Manual/90/en to Translations:KAVAN AP06A - Instruction Manual/90/en without leaving a redirect: Part of translatable page "Kavan AP06A - Instruction Manual"

FuzzyBot: Importing a new version from external source