Translations:KAVAN ESCs - Instruction manual/23/de - Revision history

Mr. KAVAN at 07:22, 28 January 2025

2025-01-28T07:22:23Z

← Older revision		Revision as of 09:22, 28 January 2025
Line 1:		Line 1:
	=== Problemlösungen ===		=== Problemlösungen ===
	{\| class="wikitable"		{\| class="wikitable" style="width: 100%; text-align: center;"
	!'''Problem'''		!'''Problem'''
	!'''Möglicher Grund'''		!'''Möglicher Grund'''

Mrs. Kavan at 08:58, 3 May 2024

2024-05-03T08:58:43Z

← Older revision		Revision as of 10:58, 3 May 2024
Line 1:		Line 1:
	=== Problemlösungen ===		=== Problemlösungen ===
	{\| class="wikitable"		{\| class="wikitable"
	!'''~~Trouble~~'''		!'''Problem'''
	!'''~~Possible reason~~'''		!'''Möglicher Grund'''
	!'''~~Solution~~'''		!'''Abhilfe'''
	\|-		\|-
	\|~~After powering on~~, ~~the motor does not work and no sound is emitted~~.		\|Nach dem Einschalten arbeitet der Motor nicht, keine Töne sind zu hören.
	\|~~The connection between the battery pack and ESC is not correct~~.		\|Die Verbindung zwischen Regler und Akku ist nicht korrekt.
	\|~~Check the power connection~~. ~~Replace the connector~~.		\|Überprüfen Sie die Verbindung. Tauschen Sie die Stecker aus.
	\|-		\|-
	\|~~After powering on~~, ~~the motor does not work, such an alert tone is emitted~~: ~~"beep–beep–~~, ~~beep–beep–~~, ~~beep–beep–"~~ (~~Every "beep–beep–" has a time interval of about~~ 1 ~~second~~).		\|Nach dem Einschalten arbeitet der Motor nicht, folgender Warnton ist zu hören: „beep-beep-, beep-beep-, beep-beep-“ (jeder „beep-beep-“ hat einen Intervall von ca. 1 Sekunde).
	\|~~Input voltage is abnormal~~, ~~too high or too low~~.		\|Eingangsspannung ist nicht normal, zu hoch oder zu tief.
	\|~~Check the voltage of the battery pack~~.		\|Prüfen Sie die Spannung des Akkupack.
	\|-		\|-
	\|~~After powering on~~, ~~the motor does not work, such an alert tone is emitted~~: ~~"beep–~~, ~~beep–~~, ~~beep–"~~ (~~Every "beep–" has a time interval of about~~ 2 ~~seconds~~).		\|Nach dem Einschalten arbeitet der Motor nicht, folgender Warnton ist zu hören: „beep-, beep-, beep-“ (jeder „beep-“ hat einen Intervall von ca. 2 Sekunden).
	\|~~Throttle signal is irregular~~.		\|Gassignal ist irregulär.
	\|~~Check the receiver and transmitter~~. ~~Check the cable of the throttle channel~~.		\|Prüfen Sie Sender und Empfänger. Prüfen Sie das Anschlusskabel von Regler und Empfänger.
	\|-		\|-
	\|~~After powering on~~, ~~the motor does not work, such an alert tone is emitted~~: ~~"beep–~~, ~~beep–~~, ~~beep–"~~ (~~Every "beep–" has a time interval of about~~ 0.25 ~~seconds~~).		\|Nach dem Einschalten arbeitet der Motor nicht, folgender Warnton ist zu hören: „beep-, beep-, beep-“ (jeder „beep-“ hat einen Intervall von 0,25 Sekunden).
	\|~~The throttle stick is not~~ in ~~the bottom~~ (~~lowest~~) ~~position~~.		\|Der Gashebel ist nicht in der Neutral (tiefste) Position.
	\|~~Move the throttle stick to the bottom position~~.		\|Bewegen Sie den Gashebel in die tiefste Position.
	\|-		\|-
	\|~~After powering on~~, ~~the motor does not work, a special tone "56712" is emitted after a~~ 2-beep ~~tone (beep–beep–~~).		\|Nach dem Einschalten arbeitet der Motor nicht, folgender Warnton „56712“ ist zu hören nach 2 beep Tönen (beep-beep-).
	\| ~~The direction of the throttle channel is reversed~~, ~~so the ESC has entered the program mode~~.		\| Gasweg ist umgekehrt, Regler schaltet in Programmiermodus.
	\|~~Set the direction of the throttle channel correctly~~.		\|Stellen Sie die Gaslaufrichtung korrekt ein.
	\|-		\|-
	\|~~The motor runs~~ in ~~the opposite direction~~.		\|Motor dreht in die verkehrte Richtung.
	\|~~The direction. The connection between ESC and the motor needs to be changed~~.		\|Die Verbindung zwischen Motor und Regler muss geändert werden.
	\|~~Swap any two wire connections between ESC and motor~~.		\|Tauschen Sie zwei Verbindungskabel zwischen Motor und Regler wahllos untereinander aus.
	\|}		\|}

Mrs. Kavan: Created page with "=== Problemlösungen === {| class="wikitable" !'''Trouble''' !'''Possible reason''' !'''Solution''' |- |After powering on, the motor does not work and no sound is emitted. |The connection between the battery pack and ESC is not correct. |Check the power connection. Replace the connector. |- |After powering on, the motor does not work, such an alert tone is emitted: "beep–beep–, beep–beep–, beep–beep–" (Every "beep–beep–" has a time interval of about 1 sec..."

2024-05-03T08:53:15Z

Created page with "=== Problemlösungen === {| class="wikitable" !'''Trouble''' !'''Possible reason''' !'''Solution''' |- |After powering on, the motor does not work and no sound is emitted. |The connection between the battery pack and ESC is not correct. |Check the power connection. Replace the connector. |- |After powering on, the motor does not work, such an alert tone is emitted: "beep–beep–, beep–beep–, beep–beep–" (Every "beep–beep–" has a time interval of about 1 sec..."

New page

=== Problemlösungen ===
{| class="wikitable"
!'''Trouble'''
!'''Possible reason'''
!'''Solution'''
|-
|After powering on, the motor does not work and no sound is emitted.
|The connection between the battery pack and ESC is not correct.
|Check the power connection. Replace the connector.
|-
|After powering on, the motor does not work, such an alert tone is emitted: "beep–beep–, beep–beep–, beep–beep–" (Every "beep–beep–" has a time interval of about 1 second).
|Input voltage is abnormal, too high or too low.
|Check the voltage of the battery pack.
|-
|After powering on, the motor does not work, such an alert tone is emitted: "beep–, beep–, beep–" (Every "beep–" has a time interval of about 2 seconds).
|Throttle signal is irregular.
|Check the receiver and transmitter. Check the cable of the throttle channel.
|-
|After powering on, the motor does not work, such an alert tone is emitted: "beep–, beep–, beep–" (Every "beep–" has a time interval of about 0.25 seconds).
|The throttle stick is not in the bottom (lowest) position.
|Move the throttle stick to the bottom position.
|-
|After powering on, the motor does not work, a special tone "56712" is emitted after a 2-beep tone (beep–beep–).
| The direction of the throttle channel is reversed, so the ESC has entered the program mode.
|Set the direction of the throttle channel correctly.
|-
|The motor runs in the opposite direction.
|The direction. The connection between ESC and the motor needs to be changed.
|Swap any two wire connections between ESC and motor.
|}