Mr. KAVAN at 07:25, 28 January 2025

2025-01-28T07:25:02Z

← Older revision		Revision as of 09:25, 28 January 2025
Line 1:		Line 1:
	=== Dépannage ===		=== Dépannage ===
	{\| class="wikitable"		{\| class="wikitable" style="width: 100%; text-align: center;"
	!'''Problème'''		!'''Problème'''
	!'''Cause possible'''		!'''Cause possible'''
	!'''Solution'''		!'''Solution'''
	\|-		\|-
	\|~~After powering on~~, ~~the motor does not work and no sound is emitted~~.		\|Après la mise sous tension, le moteur ne fonctionne pas et aucun son n'est émis.
	\|~~The connection between the battery pack and~~ ESC ~~is not correct~~.		\|Le branchement entre la batterie et l'ESC n'est pas correcte.
	\|~~Check the power connection~~. ~~Replace the connector~~.		\|Vérifiez le branchement de l’'alimentation. Remplacez le connecteur.
	\|-		\|-
	\|~~After powering on~~, ~~the motor does not work~~, ~~such an alert tone is emitted~~: ~~"beep–beep–~~, ~~beep–beep–~~, ~~beep–beep–"~~ (~~Every "beep–beep–" has~~ a ~~time interval of about~~ 1 ~~second~~).		\|Après la mise sous tension, le moteur ne fonctionne pas, un tel signal sonore est émis : « bip–bip–, bip–bip–, bip–bip– » (Chaque « bip–bip– » a un intervalle d'environ 1 seconde).
	\|~~Input voltage is abnormal~~, ~~too high or too low~~.		\|La tension d'entrée est anormale, trop élevée ou trop basse.
	\|~~Check the voltage of the battery pack~~.		\|Vérifiez la tension de la batterie.
	\|-		\|-
	\|~~After powering on~~, ~~the motor does not work~~, ~~such an alert tone is emitted~~: ~~"beep–~~, ~~beep–~~, ~~beep–"~~ (~~Every "beep–" has~~ a ~~time interval of about~~ 2 ~~seconds~~).		\|Après la mise sous tension, le moteur ne fonctionne pas, un tel signal sonore est émis : « bip–, bip–, bip– » (Chaque « bip– » a un intervalle d'environ 2 secondes).
	\|~~Throttle~~ signal ~~is irregular~~.		\|Le signal du manche des gaz est irrégulier.
	\|~~Check the receiver and transmitter~~. ~~Check the cable of the throttle channel~~.		\|Vérifiez le récepteur et l'émetteur. Vérifiez le câble de la voie du manche des gaz.
	\|-		\|-
	\|~~After powering on~~, ~~the motor does not work~~, ~~such an alert tone is emitted~~: ~~"beep–~~, ~~beep–~~, ~~beep–"~~ (~~Every "beep–" has~~ a ~~time interval of about~~ 0.25 ~~seconds~~).		\|Après la mise sous tension, le moteur ne fonctionne pas, un tel signal sonore est émis : « bip–, bip–, bip– » (Chaque « bip– » a un intervalle d'environ 0,25 seconde).
	\|~~The throttle stick is not in the bottom~~ (~~lowest~~) ~~position~~.		\|Le manche des gaz n'est pas en position basse (la plus basse).
	\|~~Move the throttle stick to the bottom~~ position.		\|Déplacez le manche des gaz en position basse.
	\|-		\|-
	\|~~After powering on~~, ~~the motor does not work~~, ~~a special tone "~~56712~~" is emitted after a~~ 2~~-beep tone~~ (~~beep–beep–~~).		\|Après la mise sous tension, le moteur ne fonctionne pas, une tonalité spéciale « 56712 » est émise après un signal sonore de 2 bips (bip–bip–).
	\| ~~The direction of the throttle channel is reversed~~, ~~so the~~ ESC ~~has entered the program~~ mode.		\|Le sens de la voie du manche des gaz est inversé, donc l'ESC est entré en mode programmation.
	\|~~Set the direction of the throttle channel correctly~~.		\|Réglez correctement le sens de la voie du manche des gaz.
	\|-		\|-
	\|~~The motor runs in the opposite direction~~.		\|Le moteur tourne dans le sens inverse.
	\|~~The direction~~. ~~The connection between~~ ESC ~~and the motor needs to be changed~~.		\|Le sens de rotation. Le branchement entre l'ESC et le moteur doit être changée.
	\|~~Swap any two wire connections between~~ ESC ~~and motor~~.		\|Échangez deux branchements entre l'ESC et le moteur.
	\|}		\|}

Mr. KAVAN: Created page with "=== Dépannage === {| class="wikitable" !'''Problème''' !'''Cause possible''' !'''Solution''' |- |After powering on, the motor does not work and no sound is emitted. |The connection between the battery pack and ESC is not correct. |Check the power connection. Replace the connector. |- |After powering on, the motor does not work, such an alert tone is emitted: "beep–beep–, beep–beep–, beep–beep–" (Every "beep–beep–" has a time interval of about 1 second)...."

2025-01-28T07:20:37Z

Created page with "=== Dépannage === {| class="wikitable" !'''Problème''' !'''Cause possible''' !'''Solution''' |- |After powering on, the motor does not work and no sound is emitted. |The connection between the battery pack and ESC is not correct. |Check the power connection. Replace the connector. |- |After powering on, the motor does not work, such an alert tone is emitted: "beep–beep–, beep–beep–, beep–beep–" (Every "beep–beep–" has a time interval of about 1 second)...."

New page

=== Dépannage ===
{| class="wikitable"
!'''Problème'''
!'''Cause possible'''
!'''Solution'''
|-
|After powering on, the motor does not work and no sound is emitted.
|The connection between the battery pack and ESC is not correct.
|Check the power connection. Replace the connector.
|-
|After powering on, the motor does not work, such an alert tone is emitted: "beep–beep–, beep–beep–, beep–beep–" (Every "beep–beep–" has a time interval of about 1 second).
|Input voltage is abnormal, too high or too low.
|Check the voltage of the battery pack.
|-
|After powering on, the motor does not work, such an alert tone is emitted: "beep–, beep–, beep–" (Every "beep–" has a time interval of about 2 seconds).
|Throttle signal is irregular.
|Check the receiver and transmitter. Check the cable of the throttle channel.
|-
|After powering on, the motor does not work, such an alert tone is emitted: "beep–, beep–, beep–" (Every "beep–" has a time interval of about 0.25 seconds).
|The throttle stick is not in the bottom (lowest) position.
|Move the throttle stick to the bottom position.
|-
|After powering on, the motor does not work, a special tone "56712" is emitted after a 2-beep tone (beep–beep–).
| The direction of the throttle channel is reversed, so the ESC has entered the program mode.
|Set the direction of the throttle channel correctly.
|-
|The motor runs in the opposite direction.
|The direction. The connection between ESC and the motor needs to be changed.
|Swap any two wire connections between ESC and motor.
|}

Translations:KAVAN ESCs - Instruction manual/23/fr - Revision history

Mr. KAVAN at 07:25, 28 January 2025