FuzzyBot: Importing a new version from external source

2024-09-18T12:59:32Z

Importing a new version from external source

← Older revision		Revision as of 14:59, 18 September 2024
Line 4:		Line 4:
	# The flight pack is to be placed in the bay in the centre of the cockpit; use the installed hook-and-lop ties to fasten it. With your radio on, set the servos to the neutral position (sticks and trims centred) and fasten the setting screws of the pushrod connectors on the elevator and rudder servo arms. Perform the throttle range calibration of the ESC as described in the attachment of this manual. '''(Fig. 6)'''		# The flight pack is to be placed in the bay in the centre of the cockpit; use the installed hook-and-lop ties to fasten it. With your radio on, set the servos to the neutral position (sticks and trims centred) and fasten the setting screws of the pushrod connectors on the elevator and rudder servo arms. Perform the throttle range calibration of the ESC as described in the attachment of this manual. '''(Fig. 6)'''
	# Attach the canopy.		# Attach the canopy.
	{{Note\|type=info\|text='''Note:''' The kit is supplied with the connection board for ailerons, flaps, elevator, rudder servos and the ESC so you can use even the most basic 6-channel radios to control your PULSE 2200 V2. If you intend to use independent control of aileron and flap servos and an advanced computer radio, you will have to bypass the connection board accordingly.}}		{{Note\|type=info\|text='''Note:''' The kit is supplied with the connection board for ailerons, flaps, elevator, rudder servos and the ESC so you can use even the most basic 6-channel radios to control your PULSE 2200 V2. If you intend to use independent control of aileron and flap servos and an advanced computer radio, you will have to bypass the connection board accordingly with a pair of wing reduction cables (e.g. [https://kavanrc.com/item/kavan-wing-reduction-jst-xh-to-2x-jr-165102 KAV02.8091.9]).}}

FuzzyBot: Importing a new version from external source

2024-05-10T06:34:15Z

Importing a new version from external source

New page

# Slide the halves of the horizontal tailplane onto the carbon joiner inserted into the fin. Secure them with four 2.5×8 mm screws. Attach the elevator push rod to the ball link on the elevator horn. '''(Fig. 1+2+3)'''
# Connect the wing multi connectors to the corresponding sockets in the wing halves. Insert both the wing halves all the way into the opening in the fuselage until you hear a click. Secure the wing with one M6×40 mm nylon screw. '''(Fig. 4+5)'''
# Hook up your receiver, servos and ESC following the wiring diagram '''(Fig. 8)'''. The receiver is to be secured with a strip of double-sided foam tape or hook-and-loop tape to the rear part of the cockpit. Deploy the antennas, so their active parts are square to each other (if you are using a receiver featuring diversity antennas).
# The flight pack is to be placed in the bay in the centre of the cockpit; use the installed hook-and-lop ties to fasten it. With your radio on, set the servos to the neutral position (sticks and trims centred) and fasten the setting screws of the pushrod connectors on the elevator and rudder servo arms. Perform the throttle range calibration of the ESC as described in the attachment of this manual. '''(Fig. 6)'''
# Attach the canopy.
{{Note|type=info|text='''Note:''' The kit is supplied with the connection board for ailerons, flaps, elevator, rudder servos and the ESC so you can use even the most basic 6-channel radios to control your PULSE 2200 V2. If you intend to use independent control of aileron and flap servos and an advanced computer radio, you will have to bypass the connection board accordingly.}}

Translations:KAVAN Pulse 2200 V2 - Instruction manual/16/en - Revision history

FuzzyBot: Importing a new version from external source

FuzzyBot: Importing a new version from external source