Translations:KAVAN R6 - User manual/55/en - Revision history

FuzzyBot: Importing a new version from external source

2025-12-16T10:22:02Z

Importing a new version from external source

← Older revision		Revision as of 12:22, 16 December 2025
Line 1:		Line 1:
	'''Custom:''' The receiver keeps the rate values on all channels as you preselect it. Select the Fail-safe setting menu. Switch from Disconnect/Hold/Not Set to "Custom". Select the channel for which you want to set fail-safe rates and confirm the selection. Then set the rates on each desired channel and confirm the selection. Wait 9 seconds for the Fail-safe setting change to take effect.		'''Custom:''' The receiver keeps the rate values on all channels as you preselect them. Select the Fail-safe setting menu. Switch from Disconnect/Hold/Not Set to "Custom". Select the channel for which you want to set fail-safe rates and confirm the selection. Then set the rates on each desired channel and confirm the selection. Wait 9 seconds for the Fail-safe setting change to take effect.
	{{Note\|type=info\|'''Note:''' If fail-safe is not set, the model will always operate with the last functional state of the channels before the signal loss. This could cause ~~potential~~ damage. If fail-safe is disabled on the RF module side, the receiver will go to the default Hold mode. Do not set the Fail-safe mode for the ~~SBUS~~ port to No Signal mode as the signal would be continuously transmitted~~, set~~ the ~~SBUS~~ port to Hold or Custom mode.}}		{{Note\|type=info\|'''Note:''' If the fail-safe is not set, the model will always operate with the last functional state of the channels before the signal loss. This could potentially cause damage. If the fail-safe is disabled on the RF module side, the receiver will go to the default Hold mode. Do not set the Fail-safe mode for the S.BUS port to No Signal mode, as the signal would be continuously transmitted. Set the S.BUS port to Hold or Custom mode instead.}}

FuzzyBot: Importing a new version from external source

2024-05-07T09:59:38Z

Importing a new version from external source

← Older revision		Revision as of 11:59, 7 May 2024
Line 1:		Line 1:
	'''Custom:''' The receiver keeps the rate values on all channels as you preselect it. Select the Fail-safe setting menu. Switch from Disconnect/Hold/Not Set to "Custom". Select the channel for which you want to set fail-safe rates and confirm the selection. Then set the rates on each desired channel and confirm the selection. Wait 9 seconds for the Fail-safe setting change to take effect.		'''Custom:''' The receiver keeps the rate values on all channels as you preselect it. Select the Fail-safe setting menu. Switch from Disconnect/Hold/Not Set to "Custom". Select the channel for which you want to set fail-safe rates and confirm the selection. Then set the rates on each desired channel and confirm the selection. Wait 9 seconds for the Fail-safe setting change to take effect.
	'''Note:''' If fail-safe is not set, the model will always operate with the last functional state of the channels before signal loss. This could cause potential damage. If fail-safe is disabled on the RF module side, the receiver will go to the default Hold mode. Do not set the Fail-safe mode for the SBUS port to No Signal mode as the signal would be continuously transmitted, set the SBUS port to Hold or Custom mode.		{{Note\|type=info\|'''Note:''' If fail-safe is not set, the model will always operate with the last functional state of the channels before the signal loss. This could cause potential damage. If fail-safe is disabled on the RF module side, the receiver will go to the default Hold mode. Do not set the Fail-safe mode for the SBUS port to No Signal mode as the signal would be continuously transmitted, set the SBUS port to Hold or Custom mode.}}

FuzzyBot: Importing a new version from external source

2024-05-06T12:48:58Z

Importing a new version from external source

← Older revision		Revision as of 14:48, 6 May 2024
Line 1:		Line 1:
	'''Custom:''' ~~the~~ receiver keeps the rate values on all channels as you preselect it. Select the Fail-safe setting menu. Switch from Disconnect/Hold/Not Set to "Custom". Select the channel for which you want to set fail-safe rates and confirm the selection. Then set the rates on each desired channel and confirm the selection. Wait 9 seconds for the Fail-safe setting change to take effect.		'''Custom:''' The receiver keeps the rate values on all channels as you preselect it. Select the Fail-safe setting menu. Switch from Disconnect/Hold/Not Set to "Custom". Select the channel for which you want to set fail-safe rates and confirm the selection. Then set the rates on each desired channel and confirm the selection. Wait 9 seconds for the Fail-safe setting change to take effect.
	'''~~Notes~~:''' If fail-safe is not set, the model will always operate with the last functional state of the channels before signal loss. This could cause potential damage. If fail-safe is disabled on the RF module side, the receiver will go to the default Hold mode. Do not set the Fail-safe mode for the SBUS port to No Signal mode as the signal would be continuously transmitted, set the SBUS port to Hold or Custom mode.		'''Note:''' If fail-safe is not set, the model will always operate with the last functional state of the channels before signal loss. This could cause potential damage. If fail-safe is disabled on the RF module side, the receiver will go to the default Hold mode. Do not set the Fail-safe mode for the SBUS port to No Signal mode as the signal would be continuously transmitted, set the SBUS port to Hold or Custom mode.

FuzzyBot: Importing a new version from external source

2024-03-15T11:51:43Z

Importing a new version from external source

New page

'''Custom:''' the receiver keeps the rate values on all channels as you preselect it. Select the Fail-safe setting menu. Switch from Disconnect/Hold/Not Set to "Custom". Select the channel for which you want to set fail-safe rates and confirm the selection. Then set the rates on each desired channel and confirm the selection. Wait 9 seconds for the Fail-safe setting change to take effect.
'''Notes:''' If fail-safe is not set, the model will always operate with the last functional state of the channels before signal loss. This could cause potential damage. If fail-safe is disabled on the RF module side, the receiver will go to the default Hold mode. Do not set the Fail-safe mode for the SBUS port to No Signal mode as the signal would be continuously transmitted, set the SBUS port to Hold or Custom mode.