Translations:KAVAN V20 - Quickstart guide/5/en: Difference between revisions
No edit summary |
(Importing a new version from external source) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 1: | Line 1: | ||
* Colour backlit LCD touchscreen at 4.3" diagonal with 800×480 px resolution | * Colour backlit LCD touchscreen at 4.3" diagonal with 800×480 px resolution | ||
* Up to 20 flight modes for perfect control of your model in all conditions | * Up to 20 flight modes for perfect control of your model in all conditions | ||
* Full telemetry with data transfer from a wide range of sensors with the ability to write | * Full telemetry with data transfer from a wide range of sensors with the ability to write on an MicroSD card | ||
* Memory for 64 models expandable via | * Memory for 64 models expandable via MicroSD card | ||
* Voice telemetry output from the speaker or via cable with a 3.5mm Jack connector | * Voice telemetry output from the speaker or via cable with a 3.5mm Jack connector | ||
* Up to 2 external antennas can be connected | * Up to 2 external antennas can be connected | ||
| Line 12: | Line 12: | ||
* Programmable slider (tension potentiometer) | * Programmable slider (tension potentiometer) | ||
* 6-axis gyro sensor | * 6-axis gyro sensor | ||
* Precision | * Precision gimbals housed in 10 ball bearings | ||
* Trainer mode via cable or wirelessly via Bluetooth® | * Trainer mode via cable or wirelessly via Bluetooth® | ||
* F.BUS socket for programming servos Model names with 15 characters | * F.BUS socket for programming servos | ||
* Model names with 15 characters | |||
* Subtrims | * Subtrims | ||
* Reversing the servo operation | * Reversing the servo operation | ||
| Line 21: | Line 22: | ||
* Resetting data | * Resetting data | ||
* Fail-safe emergency rates | * Fail-safe emergency rates | ||
* | * Dual rates | ||
* Rate progression setting along 2 exponential curves or 21-point curves | * Rate progression setting along 2 exponential curves or 21-point curves | ||
* Freely programmable mixes | * Freely programmable mixes | ||
* | * Engine shutdown | ||
* Safe idle | * Safe idle | ||
* Logically linked switches | * Logically linked switches | ||
* Intuitive user | * Intuitive user interface with customizable widgets | ||
* Servo monitor and servo tester | * Servo monitor and servo tester | ||
* | * 3 timers (stopwatch or timer) | ||
* Model run time | * Model run time | ||
* Transmitter run time | * Transmitter run time | ||
| Line 37: | Line 38: | ||
* Sound and vibration warning | * Sound and vibration warning | ||
* Range check | * Range check | ||
* 3 receiver operation mode setting | * 3 receiver operation mode setting (Redundancy) | ||
Latest revision as of 11:15, 11 March 2024
- Colour backlit LCD touchscreen at 4.3" diagonal with 800×480 px resolution
- Up to 20 flight modes for perfect control of your model in all conditions
- Full telemetry with data transfer from a wide range of sensors with the ability to write on an MicroSD card
- Memory for 64 models expandable via MicroSD card
- Voice telemetry output from the speaker or via cable with a 3.5mm Jack connector
- Up to 2 external antennas can be connected
- 6 three-position switches, 2 two-position (1 momentary) switches
- 2 rotary side dials, 2 momentary buttons on the rear
- 6 user-programmable buttons (front)
- 2 programmable mixer rotary knobs
- 4 digital trims
- Programmable slider (tension potentiometer)
- 6-axis gyro sensor
- Precision gimbals housed in 10 ball bearings
- Trainer mode via cable or wirelessly via Bluetooth®
- F.BUS socket for programming servos
- Model names with 15 characters
- Subtrims
- Reversing the servo operation
- Setting end points and rate limiting
- Servo speed setting
- Resetting data
- Fail-safe emergency rates
- Dual rates
- Rate progression setting along 2 exponential curves or 21-point curves
- Freely programmable mixes
- Engine shutdown
- Safe idle
- Logically linked switches
- Intuitive user interface with customizable widgets
- Servo monitor and servo tester
- 3 timers (stopwatch or timer)
- Model run time
- Transmitter run time
- Indication of preset controller positions when the transmitter is started
- Adjustable display backlight intensity
- Calibration of gimbals
- Sound and vibration warning
- Range check
- 3 receiver operation mode setting (Redundancy)