Translations:KAVAN Alpha V2 1500mm - Instruction manual/39/en: Difference between revisions

From KAVAN RC Wiki
VisualWikitext
(Importing a new version from external source)
 
(Importing a new version from external source)
 
Line 1: Line 1:
=== RC SET INSTALLATION ===
=== RC set installation ===
Now you have to install/connect your receiver, servos and electronic speed controller (ESC).
Now you have to install/connect your receiver, servos and electronic speed controller (ESC).<br><ol style="list-style-type:decimal"><li>Remove the canopy; lift the rear part up to disengage the magnetic lock.</li><li> Following you radio instruction manual connect the servos, ESC and LED light cables to your receiver – the table shows the channel assignment of the Futaba® or RadioLink® radios - refer to your radio manual for the correct assignment:
{| class="wikitable" style="text-align: center; width: 100%;"
|+
!Connector Label
!Function
!Receiver Channel
|-
|AILE
|Ailerons
|CH1
|-
|ELEV
|Elevator
|CH2
|-
|ESC
|Throttle
|CH3
|-
|RUDD
|Rudder
|CH4
|-
|LED
|LED Lights
|CH5
|}
</li><li>Put your receiver into the fuselage under the wing seat; you can secure it using a strip of hoop-and-loop tape to the fuselage.</li><li> The flight battery pack is to be inserted into the nose of your ALPHA 1500 V2 and secured by the hoop-and-loop tape to the plywood battery trail – the exact position of the battery pack will be determined later during the Centre of Gravity position check.</li></ol>
{{Note|type=warn|'''Caution:''' Always turn on your transmitter first and only then connect the flight pack to the ESC. From now on always handle your model as if the motor might burst into life and the propeller start to spin anytime!}}

Latest revision as of 07:17, 20 October 2025

Message definition (KAVAN Alpha V2 1500mm - Instruction manual)
=== RC set installation ===
Now you have to install/connect your receiver, servos and electronic speed controller (ESC).<br><ol style="list-style-type:decimal"><li>Remove the canopy; lift the rear part up to disengage the magnetic lock.</li><li> Following you radio instruction manual connect the servos, ESC and LED light cables to your receiver – the table shows the channel assignment of the Futaba® or RadioLink® radios - refer to your radio manual for the correct assignment:
{| class="wikitable" style="text-align: center; width: 100%;"
|+
!Connector Label
!Function
!Receiver Channel
|-
|AILE
|Ailerons
|CH1
|-
|ELEV
|Elevator
|CH2
|-
|ESC
|Throttle
|CH3
|-
|RUDD
|Rudder
|CH4
|-
|LED
|LED Lights
|CH5
|}
</li><li>Put your receiver into the fuselage under the wing seat; you can secure it using a strip of hoop-and-loop tape to the fuselage.</li><li> The flight battery pack is to be inserted into the nose of your ALPHA 1500 V2 and secured by the hoop-and-loop tape to the plywood battery trail – the exact position of the battery pack will be determined later during the Centre of Gravity position check.</li></ol>
 {{Note|type=warn|'''Caution:''' Always turn on your transmitter first and only then connect the flight pack to the ESC. From now on always handle your model as if the motor might burst into life and the propeller start to spin anytime!}}

RC set installation

Now you have to install/connect your receiver, servos and electronic speed controller (ESC).

  1. Remove the canopy; lift the rear part up to disengage the magnetic lock.
  2. Following you radio instruction manual connect the servos, ESC and LED light cables to your receiver – the table shows the channel assignment of the Futaba® or RadioLink® radios - refer to your radio manual for the correct assignment:
    Connector Label Function Receiver Channel
    AILE Ailerons CH1
    ELEV Elevator CH2
    ESC Throttle CH3
    RUDD Rudder CH4
    LED LED Lights CH5
  3. Put your receiver into the fuselage under the wing seat; you can secure it using a strip of hoop-and-loop tape to the fuselage.
  4. The flight battery pack is to be inserted into the nose of your ALPHA 1500 V2 and secured by the hoop-and-loop tape to the plywood battery trail – the exact position of the battery pack will be determined later during the Centre of Gravity position check.
Caution: Always turn on your transmitter first and only then connect the flight pack to the ESC. From now on always handle your model as if the motor might burst into life and the propeller start to spin anytime!
Retrieved from "https://wiki.kavanrc.com/index.php?title=Translations:KAVAN_Alpha_V2_1500mm_-_Instruction_manual/39/en&oldid=44406"