KAVAN M+ - Návod k použití

Other languages:

Úvod

Gratulujeme k zakoupení KAVAN M+, miniaturního telemetrického přijímače s 2,4GHz přenosovým systémem ACCESS. Disponuje 16 nebo 24kanálovým režimem přes S.BUS. Odnímatelná anténa s IPEX4 konektorem . S Micro JST konektorem se hodí zejména pro KAVAN Sling MINI DLG, ale lze ho použít i s širokou řadou koptér. Díky připojení F.BUS můžete snadno a rychle přijímač spárovat s různými telemetrickými zařízeními. Přenos telemetrie funguje na vzdálenost 500–600 metrů. OTA (Over-the-Air) technologie zajišťuje pohodlné bezdrátové aktualizace firmwaru.

Pokud máte dotazy ohledně přijímače M+ a jeho provozu, kontaktujte technické a servisní pracovníky firmy KAVAN Europe s.r.o. e-mailem (info@kavanrc.com pro všeobecné technické informace, servis@kavanrc.com pro servis) nebo telefonicky (+420 466 260 133 pro všeobecné technické informace, +420 463 358 700 pro servis), v pracovní době 8–16 h, od pondělí do pátku).

Firmware

Stáhněte si nejnovější firmware KAVAN M+ v ETHOS Suite nebo na přímo:

M+ verze 2.1.14

Technické specifikace

Rozměry: 17×11,7×4 mm (D×Š×V)
Hmotnost: 1 g
Počet kanálů: 16/24 S.BUS
Provozní napětí: 3,5–10 V
Provozní proud: 16 mA @ 5 V
Provozní frekvence: 2,400–2,4835 GHz
Max. vyzářený výkon:' <14 dB (EIRP)
Provozní dosah: ＞1.2 km (*Dosah se může měnit podle lokálních podmínek)
Kompatibilita: Všechny ACCESS vysílače

Funkce

ACCESS protokol s Over-The-Air (OTA)
Miniaturní rozměry a hmotnost
Řízení v plném dosahu & dosah telemetrie na 500–600 metrů
Výstupní S.BUS
S.Port / F.Port
Invertovaný S.Port
VFR (Valid Frame Rate) telemetrie

Stavová kontrolka


Zelená	Červená	Stav
Svítí	Svítí	Registrace
Bliká	BLiká	Registrace dokončena
Svítí	Svítí	Párování
Svítí	Nesvítí	Párování dokončeno
Svítí	Nesvítí	Pracuje správně
Nesvítí	Svítí	Fail-safe režim

Registrace a párování

Před započetím používání vašeho přijímače je nutné ho nejprve zaregistrovat.

Postup:

Přepněte vysílač do stavu [Reg].
- Zapněte vysílač, přejděte na stranu 1 nabídky Model setup, zvolte Internal nebo External RF a zvolte [Reg].
Přepněte přijímač do stavu [Reg].
- Podržte párovací tlačítko na přijímači a připojte k němu akumulátor. Červená a zelená kontrolka se rozsvítí, což signalizuje stav [Reg].
V nabídce Register se přijímač zobrazí. Zvolte "Register" stisknutím [Enter]
Vypněte přijímač.
Kurzorem vyberte RX1 [Bind].
Připojte akumulátor k přijímači. Zelená kontrolka se rozbliká, což značí stav [Bind]. Zvolte přijímač. Zelená kontrolka svítí, a na vysílači se zobrazí [Bind successful].
Potvrďte párování stisknutím [Ok]. Zelená kontrolka svítí a červená nesvítí, což značí provoz v běžném režimu.

Poznámka Jakmile je přijímač zaregistrován, tlačítko už při postupu nebudete potřebovat.

How to switch the F.Port

Select the Receiver, press the ENTER button, select the Options, and choose the F.Port.

OTA ("Over The Air") firmware update

Navigate to SD CARD 2/7 and select the FW. Press the enter button, select [Flash receiver OTA], and power on the receiver. Select the RX, confirm with [ENTER] and complete the flash process. The transmitter will display [Flash successful]. Turn the receiver off and on again and wait for 3 seconds. The Green LED will start flashing, indicating the receiver works properly.

Note Please do not start another pairing in close proximity while the firmware update is in progress.

Note Update the firmware after pairing the receiver.

Range Check

A range check should be done before each flying session. Reflections from nearby metal fences, concrete buildings or trees can cause loss of signal both during range check and the flight. In Range check mode, the RF power and range are decreased to 1/30–1/10 of the normal mode.

* The signal is completely lost is recommended as the node to complete the range test.

Place the model at least 60 cm (two feet) above a non-metal contaminated surface (e.g. a wooden bench). The receiver antenna should be in a vertical position.
For Taranis X-Lite Pro as an example, turn on the transmitter and power on the receiver, go to: SETUP 2/13 /Internal RF/ Module [Rng].
For the transmitter RF module, please refer to the respective manual.

For more operation descriptions and instructions, please refer to the respective manual.

Failsafe emergency rates

When Fail-safe is turned on, 3 modes are available: No signal, Hold, Custom.

No signal: When the signal is lost, the receiver does not send a control signal to rates on any channel. To use this mode, select it from the menu and wait 9 seconds for the Fail-safe setting change to take effect.

Hold: The receiver keeps the rates as they were before the signal was lost. To use this type, select it from the menu and wait 9 seconds for the Fail-safe setting change to take effect.

Custom: The receiver keeps the rate values on all channels as you preselect them. Select the Fail-safe setting menu. Switch from Disconnect/Hold/Not Set to "Custom". Select the channel for which you want to set fail-safe rates and confirm the selection. Then set the rates on each desired channel and confirm the selection. Wait 9 seconds for the Fail-safe setting change to take effect.

Note: If the fail-safe is not set, the model will always operate with the last functional state of the channels before the signal loss. This could potentially cause damage. If the fail-safe is disabled on the RF module side, the receiver will go to the default Hold mode. Do not set the Fail-safe mode for the S.BUS port to No Signal mode, as the signal would be continuously transmitted. Set the S.BUS port to Hold or Custom mode instead.

Warranty and post-warranty service

All KAVAN® electronic products are covered by a 2-year warranty covering all manufacturing defects and faults. When claiming within the warranty period, please always present a copy of the proof of purchase with the product and provide the service personnel with as detailed and complete information as possible about the defect found, your usage and other information that will facilitate the assessment of the claim and speed up its settlement. Please make your claim at the shop where you purchased the product. If this is not possible, you can contact KAVAN Europe s.r.o. directly:

KAVAN Europe s.r.o. | Doubravice 110, 533 53 Pardubice | Czech Republic | +420 466 260 133 | info@kavanrc.com

Recycling (European Union)

Electrical equipment bearing the crossed-out bin symbol must not be disposed of in normal household waste but must instead be taken to a specialised collection and recycling facility. In EU (European Union) countries, electrical equipment must not be disposed of in normal household waste (WEEE - Waste of Electrical and Electronic Equipment, Directive 2012/19/EU). You can take unwanted equipment to your nearest collection or recycling centre. The equipment will then be disposed of or recycled safely, free of charge. By handing in your unwanted equipment, you can make an important contribution to protecting the environment.

EU declaration of conformity

KAVAN Europe s.r.o. hereby declares that the radio equipment type M+ and other equipment supplied with it comply with Directive 2014/53/EU. The full form of the EU Declaration of Conformity is available at the following website: http://www.kavanrc.com/doc. This 2.4GHz radio equipment can be used without prior registration or individual approval in all countries of the European Union.

Warranty and limitation of liability

As the manufacturer of this product, we have no control over your compliance with these instructions when wiring and installing the receiver into your model. Likewise, we have no control over how you build, operate and maintain the parts of the receiver. For this reason, KAVAN must disclaim all liability for any loss, damage or financial cost that is caused by the improper use or operation of products imported by us, or that is in any way connected with such activity.

Except as otherwise provided by law, KAVAN's obligation to pay compensation shall (regardless of the legal arguments asserted) be limited to the purchase price for those KAVAN products that were directly involved in the event that caused the damage. This does not apply if the manufacturer has been judicially obliged to make unlimited compensation on the basis of proven wilful or reckless negligence. We warrant that our products are in compliance with current legal provisions. The warranty does not cover failures and defects caused by:

Misuse or improper use.
Delayed, improper or no maintenance, or maintenance performed by unauthorised service.
Incorrect wiring.
Use of accessories not approved or recommended by KAVAN Europe s.r.o.
Modifications or repairs not carried out by an authorised KAVAN Europe s.r.o.
Inadvertent or deliberate damage.
Normal wear and tear.
Operation of the equipment outside the operating limits specified in the specification

KAVAN Europe s.r.o. warrants that this product is free from defects in both material and workmanship at the time of sale. KAVAN Europe s.r.o. also reserves the right to change or modify this warranty without notice. The equipment is subject to continuous improvement and refinement - the manufacturer reserves the right to change the design without notice.

This warranty certificate entitles you to a free warranty repair of the product supplied by KAVAN Europe s.r.o. within a period of 24 months. The warranty does not cover natural wear and tear due to normal use, as this is a product for modelling use, where the individual parts operate under much higher loads than normal toys are subjected to.

The warranty also does not cover any part of the equipment that has been improperly installed, roughly or improperly handled, or damaged in an accident, or any part of the equipment that has been repaired or altered by an unauthorised person (this includes the application of any waterproof sprays/coatings by the user). Like other fine electronics products, do not expose this equipment to high temperatures, low temperatures, moisture, dusty environments, violent mechanical shocks and impacts. Do not leave it in direct sunlight for extended periods of time.