All translations
Enter a message name below to show all available translations.
Found 3 translations.
| Name | Current message text |
|---|---|
| h čeština (cs) | ==== Nastavení Hlavní jehly ==== # Nastartujte motor a odpojte žhavení. Počkejte asi 1 minutu na zahřátí motoru. # Po zahřátí motoru dejte plný plyn a pomalu přivírejte hlavní jehlu, až motor dosáhne maximální možné otáčky. Poté hlavní jehlu pomalu otvírejte, až otáčky slyšitelně poklesnou. Pokud máte otáčkoměr, jedná se o pokles o 200-300 ot./min. # S motorem běžícím na plný plyn opatrně zvedněte příď modelu vzhůru asi v úhlu 45 stupňů. Směs by se neměla příliš ochudit, ale měli byste sluchem zaznamenat malý nárůst otáček. To je v pořádku. Pokud motor zhasíná nebo ztrácí otáčky, pokud je model nosem nahoru, je směs příliš chudá a je třeba hlavní jehlu pootevřít. Motor za chodu musí vždy vydávat zřetelnou stopu šedého kouře. {{Note|type=info|text='''Pozn.:''' otáčky motoru za letu vzrostou asi o 10-30%. Je to způsobeno tím, že se motor pohybuje a do karburátoru je nasáváno větší množství vzduchu pod vyšším tlakem, což směs ochuzuje. Navíc, jak klesá hladina paliva v nádrži, je pro motor obtížnější nasávat palivo, zvláště při akrobacii, což dále směs ochuzuje. Je proto nezbytné nastavit směs na zemi o něco bohatší, aby se toto ochuzování směsi za letu vyrovnalo. Za letu vždy sledujte výfukové plyny. Motor musí stále zanechávat viditelnou stopu bílého kouře. Pokud nevidíte kouř, je směs příliš chudá. Měli byste ihned přistát a nastavit bohatší směs.}} |
| h Deutsch (de) | ==== Einstellung der Hauptnadel ==== # Starten Sie den Motor und schalten Sie die Zündung aus. Warten Sie etwa 1 Minute, bis der Motor warm ist. # Nachdem der Motor warmgelaufen ist, geben Sie Vollgas und schließen langsam die Hauptnadel, bis der Motor die maximale Drehzahl erreicht. Dann öffnen Sie die Hauptnadel langsam, bis die Drehzahl hörbar abfällt. Wenn Sie einen Drehzahlmesser haben, ist dies ein Abfall von 200-300 UpM. # Heben Sie die Spitze des Modells vorsichtig in einem Winkel von etwa 45 Grad an, während der Motor bei Vollgas läuft. Das Gemisch sollte nicht zu mager werden, aber Sie sollten einen leichten Anstieg der Drehzahl nach Gehör feststellen. Das ist in Ordnung. Wenn der Motor stehen bleibt oder an Drehzahl verliert, wenn das Modell mit der Spitze nach oben steht, ist das Gemisch zu mager und die Hauptnadel muss ein bisschen geöffnet werden. Der Motor muss beim Betrieb immer eine deutliche Spur von grauem Rauch abgeben. {{Note|type=info|text='''Hinweis:''' Die Motordrehzahl steigt während des Fluges um etwa 10-30 %. Dies liegt daran, dass sich der Motor bewegt und mehr Luft unter höherem Druck in den Vergaser angesaugt wird, wodurch das Gemisch magerer wird. Außerdem wird es für den Motor schwieriger, Kraftstoff anzusaugen, wenn der Kraftstoffstand im Tank sinkt, insbesondere beim Kunstflug, wodurch das Gemisch noch magerer wird. Es ist daher notwendig, das Gemisch auf dem Boden etwas fetter einzustellen, um diese Gemischabmagerung während des Fluges zu kompensieren. Beobachten Sie immer die Abgase während des Fluges. Der Motor muss noch eine sichtbare Spur von weißem Rauch hinterlassen. Wenn Sie keinen Rauch sehen, ist das Gemisch zu mager. Sie sollten sofort landen und ein fetteres Gemisch einstellen.}} |
| h English (en) | ==== Setting the High Speed Needle Valve ==== # Start the engine and remove the glow starter from the glow plug. Allow the engine to warm up for about 1 minute. # After the engine has warmed up, advance the throttle to full and slowly lean the high speed valve until the engine reaches peak R.P.M. After reaching peak R.P.M. richen the mixture slightly until an audible drop in R.P.M. is heard. If you are using a tachometer this should be between a 200 - 300 R.P.M. drop. # With the engine running at full power, carefully lift the nose of the airplane about 45° into the air. The mixture should not become too lean, but you may hear a slight increase in R.P.M. This is good. If the engine sags, or loses R.P.M. when you hold the nose up, the mixture is too lean and should be set slightly richer. The engine should always exhibit a noticeable smoke trail from the exhaust. {{Note|type=info|text='''Note:''' R.P.M. will increase about 10% - 30% in the air. This is due to the forward motion of the aircraft as it is flying. Because of this forward motion, more air is entering the carburettor, at a higher force, and causes the mixture to lean out. Additionally, as the fuel level in the fuel tank goes down, fuel draw becomes more difficult for the engine, especially during aerobatics, also causing the mixture to go lean. It is imperative that you set the mixture rich while on the ground to compensate for the leaning tendencies that will happen in the air. Always watch the exhaust during your flight. The engine should leave a noticeable white smoke trail at all times. It there is no smoke trail, the engine is running too lean. You should land immediately and reset the mixture.}} |