KAVAN R10 - User manual/de

Einleitung

Herzlichen Glückwunsch zum Kauf des 10-Kanal-Telemetrieempfängers KAVAN R10. Er arbeitet mit einem gleichzeitigen Doppelfrequenz-Übertragungssystem Twin 2,4 GHz. Er verfügt über 10 hochpräzise PWM-Kanäle und 16- oder 24-Kanal-Modus über S.BUS. Zwei abnehmbare Antennen mit IPEX4-Stecker sorgen für volle Signalstärke über eine Reichweite von bis zu zehn Kilometern. Er ist besonders für Segler geeignet, kann aber auch für andere Modelle verwendet werden. Mit Redundanzunterstützung kann er als primärer Empfänger über S.BUS angeschlossen werden. Mit dem Twin 2.4GHz-Protokoll in dieser Verbindung arbeiten beide Empfänger gleichzeitig. Dank der F.BUS-Anschlussoption können Sie ihn auch einfach und schnell mit mehreren verschiedenen Telemetriegeräten verbinden, was eine bidirektionale Datenübertragung über ein einziges Kabel ermöglicht.

Er verfügt über eine fortschrittliche Interferenzunterdrückung für eine zuverlässige, stabile Signalübertragung über die gesamte Reichweite. Die intelligente Zuordnung des Übertragungssystems beschleunigt das Binden. Die Blackbox-Funktion speichert Basisflugdaten. Die Betriebszustände des Empfängers werden durch eine LED-Anzeige angezeigt. Intelligentes Binden ermöglicht drahtlose Firmware-Updates.

Er ist auch in einer stabilisierten Version erhältlich, die über verbesserte ADV-Stabilisierungsfunktionen verfügt. Die ADV-Stabilisierung bietet einen fortschrittlichen Modus mit einer Reihe von programmierbaren Kanälen.

Der klassische Stabilisierungsmodus wurde um 5 zusätzliche Stabilisierungskanäle erweitert, die ein Pin Mapping für jeden Kanal in einigen Flugmodi wie Stabilisierung, Auto-Level (Pegel halten), Hover (Schweben) und Knife-Edge (Messerflug) mit dem Flugzeugmodell ermöglichen.

Zu den fortschrittlichen Stabilisierungsfunktionen gehören hochpräzise Telemetriesensoren zur Überwachung von Höhe, vertikaler Geschwindigkeit usw.

Im Modus der erweiterten Stabilisierung sind alle Ausgangspins für die Stabilisierung und andere erweiterte Funktionen konfigurierbar, wie z. B. die gemeinsame Nutzung von Stab-Dateien, programmierbare Parameter und Zugang für Entwickler usw.

Wenn Sie Fragen zum R10-Empfänger und seiner Bedienung haben, wenden Sie sich bitte an das Technik- und Servicepersonal von KAVAN Europe s.r.o. per E-Mail (info@kavanrc.com für allgemeine technische Informationen, servis@kavanrc.com für Service) oder telefonisch (+420 466 260 133 für allgemeine technische Informationen, +420 463 358 700 für Service), während der Arbeitszeit von Montag bis Freitag von 8 bis 16 Uhr.

Firmware

Laden Sie die neueste Firmware herunter:

• Currently unavailable

Technische Daten

• RF-Übertragungssystem: Twin 2.4 GHz
• Abmessungen: 64×16.6×12.4 mm (L*B*H)
• Gewicht: 9.4 g
• Betriebsspannung: 3.5–12 V (empfohlener Akku 2S LiXX)
• Betriebsstrom: ≤120 mA bei 5 V
• Vario - Messbereich der vertikalen Geschwindigkeit: ±10 m/s
• Vario - Bereich und Auflösung des Höhenmessers: -700 m bis 10.000 m, 0.1 m
• Messbereich der externen Spannung über AIN2: 0–35 V
• Antennenanschluss: IPEX4
• Kompatibilität: Twin 2.4 GHz
• Max. Strahlungsleistung: < 20 dBm
• Arbeitsfrequenz: 2.400–2.4835 GHz

Funktionen

• Erhöhter Schutz gegen RF-Interferenzen und stabilere RF-Übertragung
• Gleichzeitiges 2,4 GHz Doppelfrequenz-Übertragungssystem mit intelligentem Binden
• Integrierte erweiterte Stabilisierungsfunktionen (R10 Stabi)
• Integrierter hochpräziser Telemetriesensor (Meereshöhe, vertikale Geschwindigkeit usw.)
• Blackbox-Funktion
• Hohe maximale Betriebsreichweite
• Drahtlose Firmware-Updates (OTA - OverTheAir)
• 10 konfigurierbare Kanäle
  • CH1: PWM / S.BUS OUT / FPort / S.Port / SBUS IN
  • CH2–10: PWM / SBUS OUT / FBUS / S.Port
• F.BUS / S.Port
• SBUS OUT Port (unterstützt 16/24CH-Modus)
• SBUS IN Port (unterstützt Signalredundanz)

Statusleuchte

Grün (LoRa)	Blau (FSK)	Rot	Status
Ein	Aus	Ein	Registrierung
Blinkt	Aus	Blinkt	Registrierung abgeschlossen
Ein	Aus	Aus	Binden
Ein	Blinkt	Aus	Binden abgeschlossen
Ein	Blinkt	Aus	Funktioniert richtig
Aus	Aus	Ein	Fail-Safe Modus

Gelb	Status (Kalibrierung des Beschleunigungsmessers)
Ein	Überschreitung der Grenzwerte (0.9G, 1.1G)
Aus	Normaler Zustand
Blinkt	Kalibrierung abgeschlossen

Gelb	Status (Autokontrolle)
Ein	Mittenerkennung verläuft
Blinkt	Erkennung vom Kanalminimum und -maximum
Aus	Autokontrolle abgeschlossen

Registrierung und Paarung

Bevor Sie Ihren Empfänger benutzen, müssen Sie ihn zunächst registrieren.

Procedure:

1. Start the registration process by selecting [Register].
2. A window will appear with the message "Waiting...." and a repeating voice message "Register".
3. Hold down the pairing button on the receiver and switch it on. Wait for the red and green LEDs to light up. The RID and UID can be set at this stage:
   • RID: This is the unique identifier of the transmitter. It can be changed to the same/own code to use the Smart share feature for model sharing (if you want to share models and own multiple transmitters, or if you share models with other modellers, you must have the same RID set on those transmitters). The RID is the transmitter data (Owner Registration ID) written into the receiver's memory. If two transmitters have the same RID, you can easily share models including receivers between them using the Smart share function.
   • RX name: the naming of the receiver is done automatically when the receiver is paired for the first time. This name can be changed at any time. This is useful when using more than one receiver, e.g. to remember the settings of the receivers, e.g. RX4R1 is for CH1–8 or RX4R2 is for CH9–16 or RX4R3 is for CH17–24.
   • UID: is used to distinguish multiple receivers used simultaneously in one model. A default value of 0 can be left for a single receiver. If more than one receiver is to be used in one model, the UID must be changed, usually 0 for CH1–8, 1 for CH9–16 and 2 for CH17–24. Note that this UID cannot be read back from the receiver, so it is a good idea to tag the receiver.
4. Press the [Register] button to complete the settings. The "Registration OK" dialog box will appear. Press the [OK] button to continue.
5. Turn off the receiver. This registers the receiver. However, you still need to pair it with the transmitter to use it.

Warning: Do not pair with an electric motor connected or with an internal combustion engine running.

Pairing

Receiver pairing allows a receiver registered in phase 1 to be paired with one of the transmitters. After that, the receiver will only communicate with that transmitter unless you pair it with another transmitter. Before using the transmitter for the first time, you must check the range of the transmitter!

1. Turn off the power to the receiver.
2. RX 1 [Pairing]: Select [Pairing] to start the pairing process. Every few seconds, a "Pairing" voice alert will sound to confirm that you are in pairing mode. A pop-up window will display the message " Waiting for receiver...".
3. Switch on the receiver without holding the F/S pairing button. A window will appear with the message "Selecting Device" and the name of the receiver you have just switched on.
4. Scroll to the receiver name and select it. A window will appear with a message that the pairing was successful.
5. Turn off the transmitter and receiver.
6. Switch on the transmitter and then the receiver. If the green LED on the receiver is lit and the red LED is not lit, the receiver is connected to the transmitter. The pairing of the receiver and transmitter will not need to be repeated unless one is replaced.

• The receiver will only be controlled by the transmitter it is paired to. Other transmitters in its vicinity do not affect its function.
• The name of the selected RX1 receiver will now be displayed next to it.
• The receiver is now ready for use.
• If redundant wiring is required, repeat for receivers 2 and 3.

IMU mode (R10 Stabi)

Note: When using the latest firmware versions of TW(≥1.0.9) Stabi-series receivers, please make sure the newest version of Stab Lua tools are running on your radio.

The devices with ADV features offer three modes to set up the stabilisation module:

• OFF mode: The stabilisation module is not activated in the mode.
• BASIC mode: The mode is enabled by default, the basic configurations can be done directly on the radio.
• ADV: The mode supports full configuration of stabilisation mode with RBmixer programmer on PC.

Note: Selecting the BASIC mode for the normal stabilisation usages. To access more flexibility in the ADV stabilisation feature, please use the RBmixer software to configure the stabilisation module.

Set the IMU mode to ADV mode and change the ADV config option from Disable to Enable, which supports parameter setting for ADV self-stabilising mode through the Upgrade interface.

Note: If you do not use the ADV advanced self-stabilising mode of the receiver, this option must be disabled.

Warning: Please ensure the ADV config is set to Disable from the SRX Basic script before a flight.

Horizontal calibration (R10 Stabi)

Note: When using the latest firmware versions of TW(≥1.0.9) Stabi-series receivers, please make sure the newest version of Stab Lua tools are running on your radio.

Click [Start] to enable the CaliHorizontal mode to do the calibration for the horizontal plane.

Note: The "CaliHorizontal" function is only activated for ADV mode horizontal calibration. It doesn't work while using the basic mode.

Two independent stabilising functions (R10 Stabi)

Note: When using the latest firmware versions of TW(≥1.0.9) Stabi-series receivers, please make sure the newest version of Stab Lua tools are running on your radio.

• Stable System page 1/2: Allows turning on/off the 1st part of stabilisation channels (CH1–6).
• Stable System page 2/2: Allows turning on/off the 2nd part of stabilisation channels (CH7–11).

Note: Press the centre button of the navigation knob to switch to the second configuration page of stabilisation channels.

Note: There are two independent stabilisation systems, calibration and self-check must be completed for both systems.

First steps - stabilisation function (R10 Stabi)

1. Create a model and make sure the connected receiver is paired with the radio.
2. Ensure stabilisation is enabled and calibrate the gyroscope sensor of the device.
3. Connect the servos and attach the stabilisation device to the model.
4. Set up the mixer channel and radio switches.
5. Determine the [Wing Type] & [Mounting Type].
6. Check the stabilised channel outputs of the receiver in the Auto-Level mode.
7. Check the stick control of the transmitter in the manual mode.
8. Start the Self-Check of the receiver.
9. Fail-safe setting.

Note: Please move to the [DOWNLOAD] section from the product page to download the functional Lua scripts (Place the decompressed folder in the root directory of the [Scripts] folder on the memory card to use.)

Gyroscope calibration

Ensure the stabilisation function is enabled

Move to the [SRX Cali] tool and calibrate the gyroscope sensor

1. The gyroscope of the device (6 surfaces) must be calibrated before mounting into the model. Place the device on a flat surface and follow the instructions below to calibrate the gyroscope.
2. Make sure the stabilisation device is lying on the surface with the logo/label facing upwards. Move to the radio and enter the [SRX Cali] tool and select "click to confirm". At this moment, the yellow LED light will flash. After it turns off, follow the prompts to calibrate the sensor.
3. Complete the calibration of all the device surfaces. Ensure the value of each axis (X, Y, Z, Mod) is about 1.000 while placing the device in the corresponding direction. The deviation should be within ±0.1.
4. The calibration is completed if all the steps above are done.

Servo connection & Build the device to the model

Connect the servos to the ports of the stabilization device according to the Channel List.

Note: Please make sure the receiver's Pins 6–10 face forward in the nose direction, and the other pins face backwards.

Channel	Corresponding tag	Control surface
CH1	AIL 1	Aileron
CH2	ELE 1	Elevator
CH3	THR	Throttle
CH4	RUD	Rudder
CH5	AIL 2	Aileron
CH6	ELE 2	Elevator
CH7	AIL 3	Aileron
CH8	ELE 3	Elevator
CH9	RUD 2	Rudder
CH10	AIL 4	Aileron
CH11	ELE 4	Elevator
CH12	User-defined	\
CH13	User-defined	Gyro gain adjustments
CH14+CH15	User-defined	Flight modes

Gyro gain adjustment of CH13: When the value of CH13 is in the centre, the gain is zero. The gain increases with the value. When the value is ±100%, the gain is at maximum.

Warning: CH1–CH12 should be connected to the corresponding servos.

Set up the mixer channel and radio switches

Refer to the Channel List to set the channel and switches. The switch setting of CH13–CH15 on the picture is for reference.

Move to the [SRx stab] tool, determine the [Wing Type] & [Mounting Type]

[Gain] and [Offset] configurations of flight modes

1. Gain - Stab mode
2. Gain - Auto-level mode
3. Gain - Hover mode
4. Gain - Knife mode
5. Angle offset - Auto-level mode
6. Angle offset - Hover mode
7. Angle offset - Knife mode

Check whether the reaction of the wing servo is in line with the flight attitude caption below in the [Auto-Level] mode. If not, please try to invert the corresponding channel output in the [SRX Stab] tool.

Stick priority & Reversed stick priority for AIL1/2, RUD and ELE1/2 channels

Note: The stabilised feature turns invalid if the output values of the stick operations on these channels exceed the set values for the stick priority here.

Inspection of flight attitude

To ensure flight safety, checking the compensation direction of the model is strongly recommended. Activating auto level mode will produce a strong deflection on AIL and ELE, which is used to check the response of the aileron and elevator. Also, activating the Knife-edge and Hover mode will result in the same reaction on the rudder.

When the plane is rotated left or right (Roll), ailerons should have the correcting actions as illustrated.

When the plane is rotated up or down (Pitch), elevators should have the correcting actions as illustrated.

When the plane is rotated to left or right (Yaw), rudders should have the correcting actions as illustrated.

Note: If the compensation direction is incorrect, please reverse the corresponding channel as illustrated above through the [SRX Stab] tool.

Check whether the reaction of the wing servo is in line with the radio stick operation in the [Manual] mode. If not, please try to invert the corresponding channel output by pressing the channel bar in the [Output] tool.

Self-check (R10 Stabi)

1. Make sure the model is in a horizontal position on the ground, then put the throttle to 0, and keep the other channels in the centre position.
2. Move to [System] and enter the [SRX Stab] tool, then click [Start] and the blue LED light turns on. Once the blue LED starts flashing, we can calibrate the maximum travel of stick channels (excluding the throttle channel).
3. If the calibration is completed, the LED turns off and the servos react left and right to indicate the calibration process is completed.

Note: To do the Self-check of the stabilisation device, please ensure the stabilisation function is enabled. Enter the [SRX Stab] tool and turn On the [Stabilising], then quit the [SRX Stab] tool and back into this tool again, now the [Self-check] can be enabled.

Setting the flight modes (R10 Stabi)

Quick mode

It supports stabilisation mode, auto-level mode, and manual (Gyroscope is off) mode and is configured through CH14. The precise configuration is written below.

Note: The default mode of R10 Stabi is Quick Mode.

• If Quick Mode is applied, there is no Knife-Edge or (3D) Hover Mode.
• CH15 is not used when using Quick Mode.

Enable the Quick Mode in the [SRX Stab] tool.

Channel	Position	Flight mode
CH14 (3-pos switch)	SW down	None
	SW middle	Stabilisation mode
	SW up	Automatic level mode

Conventional mode

It supports stabilisation mode and manual mode (the Gyroscope is off) and is configured through CH14&15. Detailed configuration is described below.

Flight mode	Stabilisation	Automatic level	Hover	Knife-edge	Off
CH14 (3-pos switch)	CH14 SW down & CH15 SW mid	CH14 SW down & CH15 SW down	CH14 SW down & CH15 SW up	CH14 SW up & CH15 SW mid	CH14 SW mid
CH15 (3-pos switch)

Model configuration reference (R10 Stabi)

Conventional model

Flight mode	Stabilisation	Automatic level	Hover	Knife-edge	Off
CH14 (3-pos switch)	CH14 > M+H (CH14 sw. down)	CH14 > M+H (CH14 sw. down)	CH14 > M+H (CH14 sw. down)	CH14 < M-H (CH14 sw. up)	CH14 sw. mid
CH15 (3-pos switch)	M-H < CH15 < M+H (CH15 sw. mid)	CH15 > M+H (CH15 sw. down)	CH15 < M-H (CH15 sw. up)	M-H < CH15 < M+H (CH15 sw. mid)

Note:

• M: represents a neutral signal period (1500 μs)
• H: represents the time of required signal change to activate the mode (50 μs). When the factory settings are selected, the switch position shown above represents the required modes.

Deltra wing / Flying wing / V-Tail

The available flight modes can be assigned to CH14 with a three-position switch.

Flight mode	Stabilisation	Automatic level	Off
CH14	CH14 > M+H (CH14 sw. down)	CH14 < M-H (CH14 sw. up)	CH14 sw. mid

1. When the Delta wing/Flying wing is selected, the signal produced by the transmitter should be without active mixes on the channels related to AIL and ELE. R10 Stabi will mix the AIL (CH1) and ELE (CH2) input signal with a fixed mix percentage automatically.
2. When the V-tail type is selected, the signal produced by the transmitter should be without active mixes on the channels related to ELE and RUD. R10 Stabi will mix the ELE (CH2) and RUD (CH4) input signal with a fixed mix percentage automatically.

Stabilisation: When the model is activated, R10 Stabi will compensate for external forces (wind) as soon as it receives commands from the transmitter. This function is used to enhance the stability of the model on three axes (Pitch, Roll, YAW). CH13 could be used to adjust gyro gain by assigning a knob or a slider, changing the sensitivity of the counteracting signal produced by the internal three-axis gyroscope.

Automatic level: When the mode is activated, R10 Stabi will make the model return to level orientation with an internal three-axis accelerometer and three-axis gyroscope on AIL and ELE channels after the sticks are released to neutral. RUD channel works in stabilisation mode only.

Hover: When the mode is activated, R10 Stabi will make the nose of the model straight up with an internal three-axis accelerometer and three-axis gyroscope on RUD and ELE channels (ELE and RUD inputs are not required). Under this mode, AIL is used to control the rotation of the model and THR to adjust the altitude. AIL channel works in stabilisation mode only.

Knife-edge mode: When the mode is activated, R10 Stabi will roll the plane on a certain side (wing points up) with an internal three-axis accelerometer and three-axis gyroscope on RUD and AIL channels. Thus, AIL inputs are not required. While the mode steering is done with ELE, altitude will be maintained with THR/RUD. ELE channel operates in stabilisation mode only.

Off: When the mode is activated, R10 Stabi will transmit the received commands produced by the transmitter to the model without compensating.

Roll and Pitch Angle throws configuration in Stab mode (R10 Stabi)

Warning: Make sure the [SRX Stab] script tool has been downloaded and placed in the [Scripts] folder of the storage card. The tool can be found under the [System] menu page after rebooting the ETHOS system.

Ensure the receiver is bound to the radio and its Stab data is readable through Lua script. The movement angle of Roll and Pitch for Stab mode can be configured up to 80 degrees.

Warning: This feature will not be activated if the degree value is set to 0–9. The setting with the Roll/Pitch degree between 10–80° can have the feature work, and it's not recommended to be set with the degree values too small.

Turning on the High PWM speed mode

1. The factory default setting is OFF.
2. To go to the receiver [Options], select On to activate the High speed mode.

Warning: High PWM speed mode is only applied for digital servos. Turn off High PWM Speed mode when using an analogue servo, otherwise, servos will get hot and may burn out.

Choosing S.Port/SBUS OUT/SBUS IN/FBUS

1. Enter the [Set] of the receiver.
2. Select the FBUS/S.Port/SBUS Out/SBUS In for the channel ports.

Choosing the SBUS-16/24 mode

1. Enter the RX Settings.
2. Click [SBUS], then select SBUS-16 mode or SBUS-24 mode.

Black box

The Black box records flight data, e.g. RX Reset Case, RSSI, VFR etc. For KAVAN V20 as an example, to get flight data, please go to RF System-[Set]-[Flight Data Record].

OTA function

Go to the [File manager], select the FW, press the enter button and select [Flash RX by int.OTA]. Power on the receiver, select the RX, go to the [ENTER], complete the flash process and the transmitter will display [Success]. Wait for 3 seconds, the receiver works properly at the moment.

Note: Please do not start binding in near proximity while the firmware upgrade is in progress.

Note: Update the firmware after registering the receiver (OTA).

Range check

A range check should be made before each flight in case signal loss is caused by reflection from metal or concrete structures and shadowing of the signal by buildings or trees during flight.

1. Place the model at least 60 cm on a non-metallic base (e.g. on a wooden bench). The receiving antenna should be in a vertical position.
2. Enter the ETHOS system, go to "VF system", select the "RANGE" mode and press [ENTER]. In the range check mode, the effective range is reduced to 1/30.

Fail-safe emergency rates

After enabling Fail-safe, there are 3 modes available: No signal, Hold, and Custom.

No signal: When the signal is lost, the receiver does not send a control signal to the deflectors on any channel. To use this type, select it from the menu and wait 9 seconds for the Fail-safe setting change to take effect.

Hold: The receiver maintains the deflections as they were before the signal was lost. To use this type, select it from the menu and wait 9 seconds for the Fail-safe setting change to take effect.

Custom: The receiver maintains the deflection value on all channels as you pre-select it. Select the Fail-safe setting menu. Switch from Disconnect/Hold/Not set to "Custom". Select the channel for which you want to set fail-safe deflections and confirm the selection. Then set the deflections on each desired channel and confirm the selection. Wait 9 seconds for the Fail-safe setting change to take effect.

Note:

• If the failsafe is not set, the model will always work with the last working status before the signal is lost. That could cause potential damage.
• When the failsafe is disabled on the RF module side, the receiver defaults to Hold mode.
• When in No Signal Mode, do not set the Failsafe to No Signal Mode for the SBUS port as it will keep the signal output continuous. Set "Hold" or "Custom" mode for the SBUS port.

Warranty and post-warranty service

All KAVAN® electronic products are covered by a 2-year warranty covering all manufacturing defects and faults. When claiming within the warranty period, please always present a copy of the proof of purchase with the product and provide service personnel with as detailed and complete information as possible about the defect found, your usage and other information that will facilitate the assessment of the claim and speed up its settlement.  Please make your claim at the shop where you purchased the product. If this is not possible, you can contact KAVAN Europe s.r.o. directly:

KAVAN Europe s.r.o. | Doubravice 110, 533 Pardubice | Czech Republic | +420 466 260 133 | info@kavanrc.com

Warranty and limitation of liability

As the manufacturer of this product, we have no control over your compliance with these instructions when wiring and installing the RC set into your model. Likewise, we have no control over the way you build, operate and maintain the RC set parts. For this reason, KAVAN must disclaim all liability for any loss, damage or financial cost that is caused by the improper use or operation of products imported by us, or that is in any way connected with such activity.

Except as otherwise provided by law, KAVAN‘s obligation to pay compensation shall (regardless of the legal arguments asserted) be limited to the purchase price for those KAVAN products that were directly involved in the event that caused the damage. This does not apply if the manufacturer has been judicially obliged to make unlimited compensation on the basis of proven wilful or gross negligence. We warrant that our products are in compliance with current legal provisions. The warranty does not cover failures and defects caused by:

• Misuse or improper use.
• Delayed, improper or no maintenance, or maintenance performed by unauthorized service.
• Incorrect wiring.
• Use of accessories not approved or recommended by KAVAN Europe s.r.o.
• Modifications or repairs not carried out by an authorised KAVAN Europe s.r.o.
• Inadvertent or deliberate damage.
• Normal wear and tear.
• Operation of the equipment outside the operating limits specified in the specification

KAVAN Europe s.r.o. warrants that this product is free from defects in both material and workmanship at the time of sale. KAVAN Europe s.r.o. also reserves the right to change or modify this warranty without notice. The equipment is subject to continuous improvement and refinement - the manufacturer reserves the right to change the design without notice.

This warranty certificate entitles you to a free warranty repair of the product supplied by KAVAN Europe s.r.o. within a period of 24 months. The warranty does not cover natural wear and tear due to normal use, as this is a product for modelling use, where the individual parts operate under much higher loads than normal toys are subjected to.

The warranty also does not cover any part of the equipment that has been improperly installed, roughly or improperly handled, or damaged in an accident, or any part of the equipment that has been repaired or altered by an unauthorized person (this includes the application of any waterproof sprays/coatings by the user). Like other fine electronics products, do not expose this equipment to high temperatures, low temperatures, moisture, dusty environments, violent mechanical shocks or impacts. Do not leave it in direct sunlight for extended periods.

Please claim warranty repairs from the shop where you purchased the set.

Recycling (European Union)

Electrical equipment bearing the crossed-out bin symbol must not be disposed of in normal household waste but must instead be taken to a specialised collection and recycling facility. In EU (European Union) countries, electrical equipment must not be disposed of in normal household waste (WEEE - Waste of Electrical and Electronic Equipment, Directive 2012/19/EU). You can take unwanted equipment to your nearest collection or recycling centre. The equipment will then be disposed of or recycled safely free of charge. By handing in your unwanted equipment, you can make an important contribution to protecting the environment.

EU declaration of conformity

KAVAN Europe s.r.o. hereby declares that the radio equipment type R10 and other equipment supplied with it are in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following website: http://www.kavanrc.com/doc. This 2.4GHz radio equipment can be used without prior registration or individual approval in all countries of the European Union.