KAVAN Pulse 2200 V2 - Instruction manual
Introduction
Congratulations on your purchase of the Pulse 2200 V2, motor-powered glider. You are about to start assembling a model manufactured from virtually unbreakable EPO (expanded polyolefin) foam powered by a mighty brushless motor and lightweight LiPo battery. Everybody who has already mastered flying a "full house" trainer – with aileron, elevator, rudder, and throttle control will enjoy this beautiful high-performance glider.
However, if you have not flown any other RC model yet, please put your Pulse 2200 V2 aside for a while – at least until you become familiar with any of the trainers like KAVAN BETA 1400 or ALPHA 1500. You can purchase any of these planes as RTF or ARTF kits. Please note that even the most famous glider pilots started their careers flying an elementary trainer first. After a lot of hours at the controls of a twin-seater (like the famous Czech L-13/23 Blanik) they had made their first solo flight and only then they could fly all those high-performance gliders.
Before you start
- If you are not an experienced RC pilot, plan to have a fully competent pilot check your completed model and help you with your first flights. Even though we have tried to provide you with a thorough instruction manual, RC models are rather complicated. An experienced modeller can quickly check over your model to make sure your first flights are successful.
- Please assemble your model exactly according to these instructions. Do not attempt to modify or change your model in any way as doing so may adversely change its flying characteristics.
- Before you begin, please check the entire contents of this kit to make sure no parts are missing or damaged. This will also help you to become familiar with each component of your plane. If you find that any of the parts are either missing or damaged, please contact your dealer immediately for replacement.Note: Your dealer cannot accept kits for return if construction has begun.
- Trial fit each part before glueing it in place. Make sure you are using the correct part, and that it fits well before assembling. No amount of glue can make up for a poorly fitting part.
- The manual contains a drawing showing the default position of the Centre of Gravity (CG) and recommended control surface throws. Please note it is essential to keep the recommended CG position for the first flight otherwise the model could be unstable, hard to control or even unable to fly at all. Later you can fine-tune the CG position to suit your flying style and skills.
Precautions
This RC model is not a toy. Use it with care and strictly following the instructions in this manual.
Assemble this model following strictly these instructions. DO NOT modify or alter the model. Failure to do so, the warranty will lapse automatically. Follow the instructions to obtain a safe and solid model at the end of the assembly.
Children under the age of 14 must operate the model under the supervision of an adult. Assure that the model is in perfect condition before every flight, taking care that all the equipment works correctly and that the model is undamaged in its structure.
Fly only on days with a light breeze and in a safe place away from any obstacles.
Safety precautions and warnings
- An RC aeroplane is not a toy! If misused, it can cause serious bodily harm and damage to property. Fly only in a safe place following all instructions and recommendations in this manual. Beware of the propeller! Keep loose items that can get entangled in the propeller away from the spinning propeller, including loose clothing, or other objects such as pencils and screwdrivers. Ensure that your and other people’s hands, and faces are kept away from the rotating propeller.
- As the user of this product, you are solely responsible for operating it in a manner that does not endanger yourself and others or result in damage to the product or the property of others. This model is controlled by a radio signal that is subject to interference from many sources outside your control. This interference can cause momentary loss of control so it is advisable to always keep a safe distance in all directions around your model, as this margin will help to avoid collisions or injury.
- Never operate your model with low transmitter batteries.
- Always operate your model in an open area away from power lines, cars, traffic or people. Avoid operating your model in populated areas where injury or damage can occur.
- Carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable batteries, etc.) which you use.
- Keep all chemicals, small parts and anything electrical out of the reach of children.
- Moisture causes damage to electronics. Avoid water exposure to all equipment not specifically designed and protected for this purpose.
- The model is mostly made of plastics - it is not fireproof. It may not be exposed to higher temperatures otherwise severe distortion of the foam airframe or other damage may occur.
Specification
| Wingspan | 2206 mm |
| Length | 1266 mm |
| Wing area | 41.8 dm² |
| Weight | 1800 g |
| All–up weight | 2100–2250 g |
| Motor | C3548–750 |
| ESC | KAVAN R–50SB Plus |
| Propeller | 11×8" |
Set contents
Almost ready-to-fly model of a sailplane with the brushless motor, speed controller and servos installed, instruction manual.
You will also need
- At least 7-even channel RC set, 14.8 V 2600–4000 mAh LiPo flight pack.
- Regular modeller’s tools – modeller’s knife, screwdrivers, pliers etc.
Model assembly
- Slide the halves of the horizontal tailplane onto the carbon joiner inserted into the fin. Secure them with four 2.5×8 mm screws. Attach the elevator push rod to the ball link on the elevator horn. (Fig. 1+2+3)
- Connect the wing multi connectors to the corresponding sockets in the wing halves. Insert both the wing halves all the way into the opening in the fuselage until you hear a click. Secure the wing with one M6×40 mm nylon screw. (Fig. 4+5)
- Hook up your receiver, servos and ESC following the wiring diagram (Fig. 8). The receiver is to be secured with a strip of double-sided foam tape or hook-and-loop tape to the rear part of the cockpit. Deploy the antennas, so their active parts are square to each other (if you are using a receiver featuring diversity antennas).
- The flight pack is to be placed in the bay in the centre of the cockpit; use the installed hook-and-lop ties to fasten it. With your radio on, set the servos to the neutral position (sticks and trims centred) and fasten the setting screws of the pushrod connectors on the elevator and rudder servo arms. Perform the throttle range calibration of the ESC as described in the attachment of this manual. (Fig. 6)
- Attach the canopy.
Note: The kit is supplied with the connection board for ailerons, flaps, elevator, rudder servos and the ESC so you can use even the most basic 6-channel radios to control your PULSE 2200 V2. If you intend to use independent control of aileron and flap servos and an advanced computer radio, you will have to bypass the connection board accordingly.
RC set installation and preflight check
- Referring to the instruction manual of your radio carefully hook up the onboard electronics.
- Once everything has been correctly connected, turn on your transmitter and plug in the flight pack. Check the neutral positions and throws of all control surfaces. If you need to make the control surface throws smaller, simply move the pushrod closer to the centre on the servo arm or move it far from the control surface on the control horn. And vice versa.
| Low rate | High rate | |
| Ailerons | 20 mm up/10 mm down | 25 mm up/13 mm down |
| Ailerons (Butterfly) | 20 mm up | 20 mm up |
| Ailerons (Thermal) | 3 mm down | 3 mm down |
| Ailerons (Speed) | 3 mm up | 3 mm up |
| Elevator | ± 10 mm | ± 15 mm |
| Elevator (Butterfly) | 1-3 mm down | 1–3 mm down |
| Rudder | ± 30 mm | ± 40 mm |
| Flaps | 12 mm up/18 mm down | 12 mm up/18 mm down |
| Flaps as Ailerons | 7 mm up/3.5 mm down | 10 mm up/5 mm down |
| Flaps (Butterfly) | 30 mm down | 30 mm down |
| Flaps (Thermal) | 4 mm down | 4 mm down |
| Flaps (Speed) | 4 mm up | 4 mm up |
- The "Low rate" recommended control surface throws are suitable for a less skilled pilot and regular soaring. The "High rate" setting allows an experienced pilot to explore the full aerobatic capabilities of his model. The aileron differential (aileron down deflection reduced to 50 % of up deflection) is only possible with a computer radio.
- Check the direction of rotation of the propeller. If it was incorrect, simply swap any two of the three wires between the ESC and motor or program the ESC (refer to the ESC manual).
- Check the correct position of the centre of gravity (CG) – 75–85 mm behind the leading edge of the wing (Fig. 7). Adjust the CG position by moving the flight pack – if you cannot reach the recommended position, do not hesitate to add an appropriate amount of lead to the nose or tail. An extra couple of grams won’t spoil the flying characteristics - but the incorrect CG position is a killer.
- Fully charge your flight pack and transmitter batteries, check the proper function of your radio and perform the range check of your radio according to its instruction manual. The range has to be almost the same with the motor off and at full throttle (no more than a 10 % decrease is acceptable). DO NOT try to fly unless the range check is 100% successful.
Flying
The test flying and fine-tuning is pretty much straightforward. There will be no surprise for a medium-advanced pilot who is supposed to fly this model.
Appendix
KAVAN PLUS R-15B...R-100SB
Programmable Electronic Controllers for Brushless Motors
Congratulation on your purchase of a KAVAN PLUS line electronic controller for brushless motors. The state-of-the-art KAVAN PLUS line covers almost the entire range of electric powered planes flown by a Sunday flyer. All the ESCs can be quickly programmed using your transmitter and even easier with the optional KAVAN PRO Card.
1. Warnings
- Read through the manuals of all power devices and aircraft and ensure the power configuration is rational before using this unit.
- Ensure all wires and connections are well insulated before connecting the ESC to related devices, as short circuit will damage your ESC. Ensure all devices are well connected, in order to prevent poor connections that may cause your aircraft to lose control or other unpredictable issues like damage to the device. If necessary, please use a soldering iron with enough power to solder all input/ output wires and connectors.
- Never get the motor locked up during high-speed rotation, otherwise the ESC may get destroyed and may also get your motor damaged. (Note: move the throttle stick to the bottom position or disconnect the battery immediately if the motor really gets locked up.)
- Never use this unit in the extremely hot weather or continue to use it when it gets really hot. Because high temperature will activate the ESC thermal protection or even damage your ESC.
- Always disconnect and remove batteries after use, as the ESC will continue to consume current as long as it’s still connected to batteries. Long-time contact will cause batteries to completely discharge and result in damage to batteries and/or ESC. This will not be covered under warranty.
2. Features
- The ESC features a high performance 32-bit micro processor (with a running frequency of up to 96MHz). It is compatible with various brushless motors.
- DEO (Driving Efficiency Optimization) Technology greatly improves throttle response & driving efficiency and reduces ESC temperature.
- Separate programming cable for connecting ESC to a LED program card and allows users to program the ESC anytime, anywhere. (For detailed info, please refer to the user manual of KAVAN PRO LED programming card.)
- Normal/Reverse/Linear Reverse brake modes (esp. reverse brake mode) can ef fectively shorten the landing distance for the air craft.
- Search mode can help users finding the aircraft by the alarm beeps after the aircraft lands in unclear terrain.
- Multiple protection features like start-up, ESC thermal, capacitor thermal, over-current, over-load, abnormal input voltage and throttle signal loss effectively prolong the service life of the ESC.
3. Specification
| Cont. Current | Peak Current | Input Voltage | BEC Output | Weight | Dimension | |
| KAVAN Plus R–15B | 15 A | 30 A | 2–3S LiPo | 5 V/2 A linear | 10 g | 38×17×5 mm |
| KAVAN Plus R–20B | 20 A | 40 A | 2–3S LiPo | 5 V/3 A linear | 19 g | 45×23×8 mm |
| KAVAN Plus R–30SB | 30 A | 50 A | 3–4S LiPo | 5 V/5 A switched | 33 g | 60×25×8 mm |
| KAVAN Plus R–40SB | 40 A | 60 A | 3–4S LiPo | 5 V/5 A switched | 36 g | 60×25×8 mm |
| KAVAN Plus R–50SB | 50 A | 70 A | 3–4S LiPo | 5 V/5 A switched | 36 g | 60×25×8 mm |
| KAVAN Plus R–60SB | 60 A | 80 A | 3–6S LiPo | 5 V/7 A switched | 68 g | 73×30×12 mm |
| KAVAN Plus R–80SB | 80 A | 100 A | 3–6S LiPo | 5 V/7 A switched | 79 g | 85×36×98 mm |
| KAVAN Plus R–100SB | 100 A | 120 A | 3–6S LiPo | 5 V/7 A switched | 92 g | 85×36×98 mm |
4. Connecting the ESC for the first time
- ESC wiring diagram
a) Throttle signal cable (white/red/black tri-color cable): Plug it into the throttle channel on the receiver. The white wire is for transmitting throttle signals, the red & black wires are BEC output wires.
b) Reverse brake signal wire/Programming cable (yellow wire):
• It must be plugged into any vacant channel on the receiver (when using the Reverse brake mode) to control the ON/OFF of the Reverse brake function.
• Connect it to the KAVAN PRO LED programming card if you want to program the ESC. - ESC/radio calibration
a) Turn on the transmitter and move the throttle stick to the top position.
b) Connect a battery to the ESC; the motor will sound "123" to indicate the ESC is powered on.
c) Then the motor will beep two short beeps to indicate the maximum throttle endpoint is accepted.
d) Move the throttle stick to the bottom position within 5 seconds after the two short beeps, the minimum throttle position will be accepted 1 second later.
e) The motor will beep "Number" beeps to indicate the number of LiPo cells you have plugged in.
f) The motor will beep a long beep to indicate the calibration is complete. - Normal ESC start-up procedure
a) Turn on the transmitter, and then move the throttle stick to the bottom position.
b) After connected the ESC to a battery, the motor will emit "123" to indicate the ESC is normally powered on.
c) The motor will emit several beeps to indicate the number of LiPo cells.
d) The motor emits a long beep to indicate the ESC is ready to go.
Caution: Please bear in mind improper polarity or short circuit will damage the ESC therefore it is your responsibility to double check all plugs for proper polarity, and proper connection BEFORE connecting the battery pack
for the first time.
5. Programmable functions
*) Factory default setting.
| No. | Value | 1 | 2 | 3 | 4 | 5 |
| 1 | Brake type | *Disabled | Normal | Reverse | Linear Reverse | |
| 2 | Brake force | *Disabled | Low | Medium | High | |
| 3 | Voltage cut-off type | *Soft | Hard | |||
| 4 | LiPo cells | *Auto Calc. | 2S / 3S | 3S / 4S | 5S | 6S |
| 5 | Cut-off voltage | Disabled | Low | *Medium | High | |
| 6 | Start-up mode | *Normal | Soft | Very Soft | ||
| 7 | Timing | Low | *Medium | High | ||
| 8 | Active freewheeling | *Enabled | Disabled | |||
| 9 | Search mode | *Off | 5 min | 10 min | 15 min |
- Brake type
Normal brake: Move the throttle stick to the bottom position. Function is now activated. In this mode, the brake amount equals to the brake force you’ve preset.
Reverse brake: After selected this option, the Reverse Brake signal wire (its signal range must be the same as the throttle range) must be plugged into any vacant channel on the receiver. You can control the motor direction via that channel. The channel range of 0–50 % is the default motor direction, the channel range of 50 % to 100 % will cause the motor to spin counterclockwise. The channel stick should be within the channel range of 0–50 % (0 would be better) when the first time you power on the ESC. After the Reverse function is activated, the motor will stop first and then spin in the reversed direction and then increase to the speed corresponding to the throttle input. Either signal loss, no matter reverse brake signal loss or throttle signal loss during the flight, can cause the throttle signal loss protection to be activated.
Linear reverse brake: After selected this option, the Reverse Brake signal wire must to be plugged into any vacant channel on the receiver, and you can control the motor direction via that channel. This channel should be set to a proportional control (usually a knob or slider on the transmitter). Turn the proportional control to activate the reverse function. The speed of the motor is controlled by the proportional control. When reversed, the initial throttle value is started at 10 %, and the throttle stroke of the linear switch is cured to 1.34 ms – 1.79 ms. The channel stick should be at 0 % throttle position when the first time you power on the ESC. Either signal loss, no matter reverse brake signal loss or throttle signal loss during the flight, can cause the throttle signal loss protection to be activated. - Brake force
This item is only effect in the "Normal brake" mode. The higher the level, the stronger the braking effect, where the low/medium/high corresponds to the braking force: 60 %, 90 %, 100 %. - Voltage cut-off
Soft cut-off: After selected this option, the ESC will gradually reduce the output to 60 % of the full power in 3 seconds after the low voltage cut-off protection is activated.
Hard cut-off: After selected this option, the ESC will immediately cut-off the output when the low voltage cut-off protection is activated. - LiPo cells
The ESC will automatically calculate the number of LiPo cells you have plugged in as per the "3.7 V/Cell" rule if "Auto Calc." is selected, or you can set this item manually. - Cut-off voltage
If set off, the low voltage protection function is disabled. In addition, the protection voltage value of the low voltage protection function corresponding to the low/medium/three modes is about 2.8 V/section, 3.0 V/section and 3.4 V/section. This value is the voltage of a single battery, multiplied by the number of lithium batteries automatically identified by the electronic governor or the number of lithium batteries manually set, which is the protection voltage value of the battery. (For example, if the low voltage protection threshold of 3 lithium batteries is medium, the protection voltage of the batteries is 3×3.0 = 9.0 V) - Start-up mode
This is used to adjust the throttle response time of ESC acceleration from 0 % to 100 %. Normal/soft/very soft correspond to approximately 200 ms/500 ms/800 ms respectively. - Timing
Can adjust the drive motor timing value. The low/medium and high are respectively: 5°/15°/25°. - Active freewheeling (DEO)
This item is adjustable between "Enabled" and "Disabled", and it is enabled by default. With it enabled, you can have better throttle linearity or smoother throttle response. - Search mode
After selected this option, ESC will drive the motor chirping prompt when the throttle is keep 0 % and continues to do during the set time.
6. Programming the KAVAN plus ESC
1) Using the KAVAN PRO programming card (optional)
Note: The flight pack is to be plugged in only after the LED programming card has been connected to the ESC. If your battery is already connected to your ESC, after connecting the LED programming card to the ESC, you need to disconnect the battery first and then reconnect it to the ESC to enter the programming mode to check and set parameters.
The portable KAVAN PRO LED programming card is an optional accessory applicable for field use. Its friendly interface makes the ESC programming easy and quick. Connect a battery to your ESC after connecting the KAVAN PRO LED programming card to the ESC, all programmable items will show up a few seconds later. You can select the item you want to program and the setting you want to choose via "ITEM" & "VALUE" buttons on the programming card, and then press the "OK" button to save all new settings to your ESC.
The portable KAVAN PRO LED programming card is an optional accessory applicable for field use. Its friendly interface makes the ESC programming easy and quick. Connect a battery to your ESC after connecting the KAVAN PRO LED programming card to the ESC, all programmable items will show up a few seconds later. You can select the item you want to program and the setting you want to choose via "ITEM" & "VALUE" buttons on the programming card, and then press the "OK" button to save all new settings to your ESC.
2) Programming the KAVAN plus ESC with your transmitter
Enter the programming → Select parameter items → Select parameter values → Exit the programming
I. Enter the program mode: Turn on the transmitter. Move the throttle stick to the top position. Connect a battery to the ESC. 2 seconds later, the motor will beep "B–B–" first, then emit "56712" 5 seconds later to indicate that you are in the ESC programming mode.
II. Select programmable items: After entering the programming, you’ll hear the following 11 kinds of beeps circularly. Move the throttle stick to the bottom position within 3 seconds after you hear some kind of beeps, you’ll enter the corresponding parameter item.
| 1 | "B–" | Brake type (1 short beep) |
| 2 | "B–B–" | Brake force (2 short beeps) |
| 3 | "B–B–B–" | Voltage cut-off type (3 short beeps) |
| 4 | "B–B–B–B–" | LiPo cells (4 short beeps) |
| 5 | “B——" | Cut-off voltage (1 long beep) |
| 6 | "B——B–" | Start-up mode (1 long beep & 1 short beep) |
| 7 | "B——B–B–" | Timing (1 long beep & 2 short beeps) |
| 8 | "B——B–B–B–" | Freewheeling (1 long beep & 3 short beeps) |
| 9 | "B——B–B–B–B–" | Search mode (1 long beep & 4 short beeps) |
| 10 | "B——B——" | Factory reset (2 long beeps) |
| 11 | "B——B——B–" | Exit (2 long beeps & 1 short beep) |
Note: A long "B——" equals to 5 short "B–", so a long "B——" and a short "B–" represents the 6th item in "Select parameter items".
III. Set item value (programmable value)
The motor will beep different kinds of beeps circularly. Move the throttle stick to the top position after you hear some kind of beeps will get you to the corresponding parameter value. Then you’ll hear the motor emit "1515" to indicate the value is saved, then get back to "Select parameter items" and continue to select other parameter items that you want to adjust.
| No. | Value/Sound signal | 1/B– | 2/B–B– | 3/B–B–B– | 4/B–B–B–B– | 5/B– – – – |
| 1 | Brake type | Disabled | Normal | Reverse | Linear/Reverse | |
| 2 | Brake force | Disabled | Low | Medium | High | |
| 3 | Voltage cut-off type | Soft | Hard | |||
| 4 | LiPo cells | Auto calc. | 2S / 3S | 3S / 4S | 5S | 6S |
| 5 | Cut-off voltage | Disabled | Low | Medium | High | |
| 6 | Start-up mode | Normal | Soft | Very soft | ||
| 7 | Timing | Low | Medium | High | ||
| 8 | Active freewheeling | Enabled | Disabled | |||
| 9 | Search mode | Off | 5 min | 10 min | 15 min |
IV. Exit program mode
Move the throttle stick to the bottom position within 3 seconds after you hear two long beeps and one short beep (emitting from the motor) can get you exit the programming mode. The motor beeps "Number" beeps to indicate the number of LiPo cells you have plugged in, and then a long beep to indicate the power system is ready to go.
7. Troubleshooting and protection functions
| Troubles | Warning Tones | Causes | Solutions |
|---|---|---|---|
| The ESC didn’t work after it was powered on while the motor kept beeping. | "BB, BB, BB,....." | The input voltage was beyond the operating voltage range of the ESC. | Adjust the power-on voltage and ensure it’s in the operating voltage range of the ESC. |
| The ESC didn’t work after it was powered on while the motor kept beeping. | "B–, B–, B–, B–....." | The ESC didn’t receive any throttle signal from the receiver. | Check if the transmitter and receiver are well paired, if any poor connection exists between the ESC and receiver. |
| The ESC didn’t work after it was powered on while the motor kept beeping. | "B, B, B, B....." | The throttle stick has not been moved to the bottom position. | Move the throttle stick to the bottom position and calibrate the throttle range. |
| The ESC didn’t work after the throttle calibration while the motor kept beeping. | "B, B, B, B....." | The throttle range you set was too narrow. | Re-calibrate the throttle range. |
| The ESC output suddenly reduced to 60 % during the flight, the motor kept beeping after the flight completed but the battery was still connected to the ESC. | "BB, BB, BB....." | The ESC thermal protection has been activated. | Improve the heat dissipating condition (i.e. add a cooling fan) or reduce the ESC load. |
| The ESC output suddenly reduced to 60 % during the flight, the motor kept beeping after the flight completed but the battery was still connected to the ESC. | "BBB, BBB, BBB....." | The low-voltage cut-off protection has been activated. | Change another pack. Lower down the cuto-ff voltage or disable the LVC protection (we do not recommend this). |
- Start-up protection: The ESC will monitor the motor speed during the start-up process. When the speed stops increasing or the speed increase is not stable, the ESC will take it as a start-up failure. At that time, if the throttle amount is less than 15 %, the ESC will try to restart automatically. If it is larger than 20 %, you need to move the throttle stick back to the bottom position first and then restart the ESC. (Possible causes of this problem: poor connection/disconnection between the ESC and motor wires, propellers are blocked, etc.)
- ESC thermal protection: The ESC will gradually reduce the output but won’t cut it off when the ESC temperature goes above 120 °C. For ensuring the motor can still get some power and won’t cause crashes, so the maximum reduction is about 60 % of the full power. (Here we are describing the ESC’s reaction in soft cut-off mode, while if in hard cut-off mode. It will immediately cut-off the power.)
- Throttle signal loss protection: When the ESC detects loss of signal for over 0.25 second, it will cut-off the output immediately to avoid an even greater loss which may be caused by the continuous high-speed rotation of propellers or rotor blades. The ESC will resume the corresponding output after normal signals are received.
- Overload protection: The ESC will cut off the power/output or automatically restart itself when the load suddenly increases to a very high value. (Possible cause to sudden load increase is that propellers are blocked.)
- Low voltage protection: When the battery voltage is lower than the cut-off voltage set by the ESC, the ESC will trigger the low-voltage protection. If the battery voltage is set to soft cut-off, the battery voltage will be reduced to a maximum of 60 % of the full power. When set to hard cut-off, the output is cut-off immediately. After the throttle returns to 0 %, the ESC will drive the motor to sound the alarm.
- Abnormal voltage input protection: When the battery voltage is not within the input voltage range supported by the ESC, the ESC will trigger the Abnormal input voltage protection, ESC will drive the motor to sound the alarm.
8. Safety precautions
- Do not install the propeller on the motor when you test the ESC and motor for the first time to verify the correct settings on your radio. Only install your propeller after you have confirmed that the settings on your radio is correct.
- Never use ruptured or punctured battery cells.
- Never use battery packs that are known to overheat.
- Never short circuit battery or motor terminals.
- Always use proper insulation material for cable insulation.
- Always use proper cable connectors.
- Do not exceed the number of cells or servos specified for the ESC.
- Wrong battery polarity will damage the ESC and void the warranty.
- Install the ESC in a suitable location with adequate ventilation for cooling.
- Use only batteries that are supported by the ESC and ensure the correct polarity before connecting.
- Switch your transmitter ON first and ensure the throttle stick is in the minimum position before connecting the battery pack.
- Never switch your transmitter OFF while the battery is connected to your ESC.
- Only connect your battery pack just before flying and do not leave your battery pack connected after flying.
- Handle your model with extreme care once the battery pack is connected and keep away from the propeller at all times. Never stand in-line or directly in front of any rotating parts.
- Do not immerse the ESC under the water, do not allow it to get wet while powered up.
- Always fly at a designated flying site and follow the rules and guidelines set by your modeller’s club.
Recycling and waste disposal note (European Union)
Electrical equipment marked with the crossed-out waste bin symbol must not be discarded in the domestic waste; it should be disposed of via the appropriate specialised disposal system. In the countries of the EU (European Union) electrical devices must not be discarded via the normal domestic waste system (WEEE - Waste of Electrical and Electronic Equipment, Directive 2012/19/EU). You can take your unwanted equipment to your nearest public collection point or recycling centre, where it will be disposed of in the proper manner at no charge to you. By disposing of your old equipment in a responsible manner you make an important contribution to the safeguarding of the environment!
EU declaration of conformity (European Union)
Hereby, KAVAN Europe s.r.o. declares that the model Pulse 2200 V2 and the included electronic and electric devices are in compliance with the requirements of relevant European directives and harmonized norms. The full text of the Declaration of Conformity is available at www.kavanrc.com/doc/.
Guarantee
The KAVAN Europe s.r.o. products are covered by a guarantee that fulfils the currently valid legal requirements in your country. If you wish to make a claim under guarantee, please contact the retailer from whom you first purchased the equipment. The guarantee does not cover faults which were caused in the following ways: crashes, improper use, incorrect connection, reversed polarity, maintenance work carried out late, incorrectly or not at all, or by unauthorised personnel, use of other than genuine KAVAN Europe s.r.o. accessories, modifications or repairs which were not carried out by KAVAN Europe s.r.o. or an authorised KAVAN Europe s.r.o., accidental or deliberate damage, defects caused by normal wear and tear, operation outside the Specification, or in conjunction with equipment made by other manufacturers. Please be sure to read the appropriate information sheets in the product documentation!