Translations:KAVAN TARA A1 (F1H) - Instruction manual/55/en
The kit contents
| Part | Building plan no. | Quantity |
|---|---|---|
| Fuselage block – 8 mm ceiba Plywood | (24) | 1 |
| Side cover – 3 mm poplar Plywood | (26, 28) | 2 |
| Vlies tissue sheet (1230×330 mm) | 1 | |
| Vlies tissue sheet (200×410 mm) | 1 | |
| Colour tissue trim sheet | 2 | |
| Sand paper | 1 | |
| Building plan | 1 | |
| Instruction manual | 1 | |
| Stick bundle A | ||
| Fuselage stick - spruce 2×8×595 mm | (22, 23) | 2 |
| Wing leading edge - balsa 8×8×645 mm | (2) | 1 |
| Wing main spar - spruce 3×8×645 mm | (7) | 1 |
| Stick bundle B | ||
| Wing leading edge - balsa 8×8×260 mm | (48) | 2 |
| Wing trailing edge - balsa 14×4.7×330 mm | (3a, 3b) | 2 |
| Wing trailing edge - balsa 14×4.7×260 mm | (40) | 2 |
| Spruce stick 3×5×405 mm | (11) | 1 |
| Spruce stick 3×5×395 mm | (14) | 1 |
| Spruce stick 3×5×197 mm | (10) | 2 |
| Spruce stick 3×8×245 mm | (49) | 2 |
| Balsa fuselage block – thick | (20) | 1 |
| Balsa fuselage block – thin | (21) | 1 |
| Balsa stick 3×5×300 mm | (12) | 6 |
| Rib set bag A | ||
| Main wing rib | (1) | 14 |
| Support rib | (6) | 3 |
| Wing end rib (bevelled) | (5) | 2 |
| Rib set bag B | ||
| Wing panel root rib (bevelled) | (47) | 2 |
| Wing tip | (50) | 2 |
| Wing panel rib | (41–46) | 12 |
| Bag C | ||
| Fin | (29) | 1 |
| Bottom fin | (37) | 1 |
| Wing seat plate – Plywood 1.5 mm | (36) | 1 |
| Wing centre sheeting - Balsa 1.5 mm | (4, 8, 9) | 6 |
| Small parts bag D | ||
| Balsa plate – Balsa 3 mm – 30×80 mm | (13) | 1 |
| Balsa plate – Balsa 3 mm – 30×30 mm | (16) | 1 |
| Balsa plate – Balsa 3 mm – 13.5×45 mm | (17) | 2 |
| Wing joiner "V" | (42) | 4 |
| Gusset | (10, 15, 51) | 18 |
| Small parts bag E | ||
| Rudder | (52) | 1 |
| Fin reinforcement plate | (30) | 1 |
| Rear horizontal tailplane seat – Balsa 1.5 mm – 8×10 mm | (33) | 1 |
| Towhook | (39) | 1 |
| Rubber thread Ø1×600 mm | 1 | |
| Horizontal tailplane seat – Plywood 1 mm – 25×15 mm | (31) | 1 |
| Spruce Stick – 3×5×25 mm | (32) | 1 |
| Bamboo dowel Ø2.5×25 mm | (34, 35) | 2 |
| Bamboo dowel Ø2.5×50 mm | (18) | 1 |
| Beech dowel Ø4x32 mm | (25) | 2 |
| Screw 2×8 mm | (38) | 2 |
| Ballast Ø26×8mm | (27) | 1 |
| Rudder hinge (brass tin) | (53) | 2 |