Aller au contenu principal
Attention

En cours de préparation – les traductions sont en cours. La notice en anglais est disponible ci-dessous.

Freewing F-16 Fighting Falcon 680 mm – 6S – Instruction manual

Freewing F-16 64 PNP 6S
FWFJ11113P

Freewing F-16 64 PNP 6S

Introduction​

The F-16 Fighting Falcon is a factory-built EPO radio-controlled aircraft supplied in PNP configuration. The airframe requires final assembly, a compatible radio system and the flight battery specified below. Complete the mechanical, radio and balance checks before flying. This manual covers FWFJ11113P.

Safety notes and warnings​

Danger

This model is not a toy. Incorrect assembly or operation can cause serious injury. It is intended for experienced RC pilots; inexperienced users need competent assistance. For ages 14 and above; anyone under 14 may operate it only under an adult’s instruction and supervision. Read and retain the complete instructions, including those supplied with the radio, battery, charger, ESC and any gyro.

  • Keep hands, hair, clothing and loose objects away from the EDF intakes, rotors and exhausts. A fan can draw in objects and eject debris.
  • Keep the flight battery disconnected during assembly, transport and maintenance. Connect it only when the model is secure and the propulsion area is clear. Treat the motor as live whenever power is connected.
  • Fly in an unobstructed area clear of people, animals, roads, power lines and buildings. Maintain a safe distance and follow the applicable model-flying rules at your site.
  • Do not fly in rain, poor visibility or unsuitable wind, or with a damaged airframe, weak transmitter battery or unreliable radio link.
  • Use only a compatible LiPo balance charger with the correct cell count and charging settings. Supervise charging on a non-flammable surface. Do not use damaged, swollen or overheated batteries.
  • Keep water, solvents and excessive heat away from the model and electronics. Do not leave the foam airframe or batteries in a hot vehicle or direct heat.

Keep a 2 m clear area around stored flight batteries, free of combustible and explosive materials. Take damaged or exhausted batteries to a suitable battery collection facility. Collect waste at the flying site; do not discard or burn it. Never try to catch the aircraft in flight or during landing—wait until it has stopped and the propulsion is safe.

Features​

  • Painted EPO airframe with factory-installed propulsion and servos.
  • 1× Ø64 mm EDF, 12-blade rotor.
  • Fixed landing gear.

Technical specifications​

ParameterValue
Wingspan680 mm
Length1050 mm
WeightNot confirmed (excluding drive battery)
AirframeEPO
Propulsion1× Ø64 mm EDF, 12-blade rotor
Landing gearFixed
Flight battery, not included6S LiPo; capacity to be confirmed for this version
Radio system, not includedAt least 4 channels for the basic arrangement; additional functions may require more channels
Battery compartment (verify fit)170×48×35 mm
Battery discharge ratingAt least 35C

Package contents​

Painted fuselage, wing and tail/control-surface assemblies; installed brushless propulsion, ESC and servos; linkages, specified joiners and assembly hardware; the landing gear and scale fittings supplied for this version. The transmitter, receiver, flight battery and charger are not included. Check every part against the supplied packing list before beginning; contact the supplier if anything is missing or damaged.

Required equipment​

  • A compatible transmitter and receiver with at least 4 channels for the basic functions. Allow extra channels where independent surfaces, thrust vectoring, gyro controls, wing sweep or reverse are specified.
  • A suitable flight battery: 6S LiPo; capacity to be confirmed for this version. Check its dimensions, mass, connector and cell count against the supplied power system and CG before use.
  • A LiPo balance charger suitable for the selected battery and a charged transmitter battery.
  • Suitable screwdrivers and hex drivers, pliers, a ruler/control-throw gauge, a balance stand and a padded model support.
  • EPO-compatible adhesive for the joints specified in the assembly instructions. Test compatibility first; allow the adhesive to cure fully. Use threadlocker only where specified for metal-to-metal fasteners and keep it away from plastic and foam.

Main section​

Preparation​

Danger

Leave the flight battery disconnected. Remove propellers from propeller-driven models. On an EDF model, isolate the motor connection for radio/servo work where accessible, insulating loose connectors individually; disconnect the flight battery before changing any wiring. Restore the original motor connections only for controlled propulsion checks.

  1. Inspect the foam, hinges, joiners, horns, motor mounts and installed wiring for transport damage. Identify left/right parts and the correct fasteners.
  2. Trial fit the assemblies before applying adhesive. Do not force a joint or use glue to compensate for an incorrectly fitted part.
  3. Keep servo and lighting plugs accessible while joining assemblies. Route cables through their channels and protect them from screw tips, moving linkages and landing-gear mechanisms.
  4. Use only the screws specified for each location. Tighten securely without crushing foam or stripping plastic threads.

Assembly​

Wing and tail​

Wing and tail — 1

Wing and tail — 1

Wing and tail — 2

Wing and tail — 2

Wing and tail — 3

Wing and tail — 3

Wing and tail — 4

Wing and tail — 4

Wing and tail — 5

Wing and tail — 5

Glue the left and right wingtip rails to the wings, then glue the wings to the fuselage. Glue the horizontal tailplanes into place and bond the carbon reinforcing strips into their grooves. Feed a pull wire from the battery bay through the cable channel to the tail. Use it to draw the rudder-servo lead forward while seating and gluing the fin.

Landing gear and pitot tube​

Landing gear and pitot tube — 1

Landing gear and pitot tube — 1

Landing gear and pitot tube — 2

Landing gear and pitot tube — 2

Landing gear and pitot tube — 3

Landing gear and pitot tube — 3

Landing gear and pitot tube — 4

Landing gear and pitot tube — 4

Invert the fuselage and secure the two wooden mounting pieces with four FA3×8 screws. Insert the nose-wheel assembly with its locking-screw position facing forwards and secure it with the M4×4 grub screw. Insert each main-gear assembly into its mount and check retention. Push the removable pitot tube into the nose cone; remove it again for transport.

Receiver installation and radio setup​

  1. Select the correct aircraft memory and label it with the model/version. Keep throttle at its minimum position and enable throttle cut. Bind the receiver following the binding procedure for the radio system with propulsion disabled.
  2. Connect each labelled control lead to its corresponding receiver or control-board function. Follow the board’s signal, positive and negative markings; do not assume every transmitter uses the same channel numbering. Retain the supplied BEC/UBEC wiring.
  3. Secure the receiver and any extensions. Follow the receiver’s antenna-placement requirements and keep antennas clear of power wiring, carbon reinforcement and moving parts.
  4. Centre the servos and set the mechanical neutrals described below before adjusting travel or mixes. Ensure clevises are fully engaged and fit their retaining sleeves; press ball links completely onto their balls.
  5. Program the required functions, control rates and failsafe. Set failsafe to stop the motor and verify its actual operation with propulsion disabled. Recheck after changing the receiver, transmitter memory or control-board configuration.

Use high rates with suitable expo for the maiden flight. Suggested expo on all three axes is −30 % on Futaba or +30 % on Spektrum. Check the sign convention on other systems. Adjust the two elevator halves to equal neutral positions and travel.

Flight battery and power-system check​

Use 6S LiPo; capacity to be confirmed for this version. Follow the discharge requirement in the specification table where provided, and the requirements of the supplied power system. Fit the battery without forcing the canopy or crushing wires. Use the retaining straps and a non-slip support, and adjust its position for the specified CG. Leave it disconnected while balancing and completing the installation.

  1. Check polarity and connector security with the battery disconnected. Make sure cooling inlets and outlets are clear.
  2. Switch on the transmitter with the correct model memory, throttle at minimum and throttle cut enabled. Secure the aircraft and keep everyone clear before connecting the flight battery.
  3. Wait for the ESC and any gyro to initialise. Stop if there is an unexpected tone, error indication, servo movement or motor start.
  4. Calibrate the throttle range only by the instructions for the installed ESC. Repeat when required after changing the radio system; do not use an unverified generic high-throttle startup procedure.
  5. With propulsion correctly assembled, check rotation and response in a clear area. Stop immediately if there is vibration, rubbing or an abnormal noise. Disconnect the battery before investigating.

Linkage reference​

Pushrod lengths and servo-arm/control-horn attachment positions — 1

Pushrod lengths and servo-arm/control-horn attachment positions — 1

Pushrod lengths and servo-arm/control-horn attachment positions — 2

Pushrod lengths and servo-arm/control-horn attachment positions — 2

Pushrod lengths and servo-arm/control-horn attachment positions — 3

Pushrod lengths and servo-arm/control-horn attachment positions — 3

Pushrod lengths and servo-arm/control-horn attachment positions — 4

Pushrod lengths and servo-arm/control-horn attachment positions — 4

Pushrod lengths and servo-arm/control-horn attachment positions — 5

Pushrod lengths and servo-arm/control-horn attachment positions — 5

Pushrod lengths and servo-arm/control-horn attachment positions — 6

Pushrod lengths and servo-arm/control-horn attachment positions — 6

Pushrod lengths and servo-arm/control-horn attachment positions — 7

Pushrod lengths and servo-arm/control-horn attachment positions — 7

Use the dimensions below and the measurement endpoints and hole positions shown in the drawing; changing a horn or servo-arm hole changes both travel and load. Secure the retainers and check full movement without binding.

FunctionLength (mm)Rod diameter (mm)
Rudder41.51.2
Aileron641.2
Elevator1291.5

Pre-flight preparation​

Centre of gravity​

Centre-of-gravity reference

Balance at the engraved CG marks beneath the wing, 81 mm from the illustrated reference. Use the marks and drawing together.

Check with the model completely assembled, including the selected battery, canopy and the accessories that will be flown. Keep power disconnected. Move and secure the battery to achieve the specified balance. Use the exact datum and aircraft configuration in the drawing.

Attention

Do not fly with the CG outside the specified position/range. A battery that fits physically may still prevent correct balance. Recheck after changing a battery, accessories, repairs or equipment. If the CG measurement datum or its applicability to the supplied version is uncertain, obtain confirmation before flight.

Control throws​

Aileron movement

Aileron movement

Elevator movement

Elevator movement

Rudder movement

Rudder movement

Measure each surface at the point shown in the drawing, from its specified neutral position. H1/H2 denote the two measured directions. A value given for each direction is not the total end-to-end travel. Treat transmitter percentages as reference settings; adjust the radio to reproduce the specified measured movement.

ControlLow rateHigh rate
Aileron, each direction16 mm / 60 %21 mm / 80 %
Elevator, each direction11 mm / 60 %16 mm / 80 %
Rudder, each direction18 mm / 70 %28 mm / 100 %

Set the neutrals and any specified flap compensation in Receiver installation and radio setup before checking these throws.

Control-direction check​

Check directions from behind the aircraft, with the model facing away. Test one function at a time, then combined inputs at the stick corners. Do not fly if any movement disagrees with the model’s control-direction diagram.

Command/functionRequired check
Right rollRight aileron/elevon trailing edge up; left down. Left roll reverses these movements.
Pitch upElevator/elevon trailing edges move up; a pitch-down command reverses the movement. Check both halves and the specified neutral offset.
Right yawRudder trailing edge moves right; steering follows the commanded turn where fitted. Check any split-drag-rudder or vector system by its own diagram.

Pre-flight checks​

  1. Confirm that all adhesives are cured, fasteners are secure and the wing/tail attachments are locked. Pull-check removable wings and inspect hinges, horns, ball links and clevis retainers.
  2. Confirm the CG, neutral positions, control throws, correct model memory and directions. Check every flight mode and any gyro, vectoring, flap, sweep or retract function fitted.
  3. Carry out a range test and failsafe test following the radio instructions, with propulsion disabled. Do not fly if the radio link or failsafe is unreliable.
  4. Check that batteries are charged, securely retained and undamaged. Confirm connector polarity, canopy retention and that no cable can reach the propulsion or moving mechanisms.
  5. Inspect the propulsion for damage or foreign objects. Verify that the cooling path is open and that a controlled motor check produces no abnormal vibration.
  6. Check the flying area, weather, runway/landing area and the position of other people. Have an experienced pilot check the initial setup.

Maiden flight and landing​

Make the maiden flight in calm, suitable conditions at an established model-flying site. Use the initial CG and high-rate throws specified for this model. Plan a short flight with reserve battery capacity.

High rates are recommended for the maiden flight to keep the full specified control travel available if unexpected trim or handling problems require larger corrections. Program a comfortable amount of exponential (expo) to soften the response around stick centre while retaining full control-surface travel at the stick limits. Where expo values are given in this manual, use them as a starting point and check the sign convention on your transmitter. High rates and expo do not compensate for an incorrect CG or mechanical setup; complete all balance and control checks before flying.

Climb to a safe height before trimming or testing a different rate or flap setting. Make one adjustment at a time.

Use a clear runway suited to the model and its wheels. Take off into wind, keep the wings level and avoid pulling into a steep climb before the model has flying speed. Check any flap compensation at safe altitude before using it on approach. Land into wind and reduce throttle before touchdown.

Shutdown​

  1. Stop the motor, enable throttle cut and keep the transmitter on.
  2. Disconnect all flight batteries before switching off the transmitter or retrieving the model for maintenance.
  3. Remove the battery, allow the battery and power system to cool, and inspect the airframe and propulsion.
  4. Store LiPo packs at the storage state specified for the battery. Do not leave a battery connected inside the model.

Appendix​

Maintenance and transport​

Inspect the model after every flight and particularly after a hard landing. Check foam joints, joiners, hinges, control horns, retaining screws, linkages, retract mounts and electrical connectors. Replace damaged propulsion parts; do not try to fly out a vibration. Repairs must restore alignment, strength and free control movement. Repeat the balance, control and range checks after repairs.

Clean with a soft cloth and materials compatible with the foam and paint. Keep moisture out of electronics and bearings. Remove fragile scale fittings for transport, protect the controls from pressure and support the airframe without distorting it. Disconnect batteries before removing wings or unplugging connectors.

Troubleshooting​

SymptomChecks before further operation
Motor does not armDisconnect power. Check the correct model memory, receiver binding, throttle minimum/trim, throttle cut, battery condition and connector polarity. If fitted, check that reverse is in the required startup position. Consult the installed ESC’s error indications.
Motor starts unexpectedly or runs in the wrong directionDisconnect power immediately. Check throttle direction, failsafe and wiring with propulsion disabled. Do not change motor connections while the battery is attached.
Surface moves incorrectly or bindsCheck the labelled plugs, transmitter mixes/reversing, servo-arm/horn holes and linkage geometry. Check the entire range and combined commands; repeat gyro direction checks.
Vibration or loss of powerStop and disconnect the battery. Inspect the rotor/propeller, fasteners, bearings, intake and cooling path. Check the battery within its specified operating limits and replace damaged components.
Model is unstable or requires excessive trimCheck CG, structural alignment, neutrals, mechanical play, control rates and any gyro settings. Land and investigate rather than continuing with an uncertain setup.
Airframe or control attachment loosensStop flying. Repair or replace the attachment and repeat the full assembly and pre-flight checks.

Warranty and post-warranty service​

All Freewing products are covered by a 2-year warranty covering all manufacturing defects and faults. When making a claim within the warranty period, please always present a copy of the proof of purchase with the product and provide the service personnel with as detailed and complete information as possible about the defect found, your usage and other information that will facilitate the assessment of the claim and speed up its settlement. Please make your claim at the shop where you purchased the product.

This warranty certificate entitles you to a free warranty repair of the product supplied by KAVAN Europe s.r.o. within a period of 24 months. The warranty does not cover natural wear and tear due to normal use, as this is a product for modelling use, where the individual parts operate under much higher loads than normal toys are subjected to.

The warranty also does not cover any part of the equipment that has been improperly installed, roughly or improperly handled, or damaged in an accident, or any part of the equipment that has been repaired or altered by an unauthorised person (this includes the application of any waterproof sprays/coatings by the user). Like other fine electronics products, do not expose this equipment to high temperatures, low temperatures, moisture, dusty environments, violent mechanical shocks and impacts. Do not leave it in direct sunlight for extended periods of time.

Improper installation includes inadequate mounting, mechanical strain on cables and insufficient cooling.

Please claim warranty repairs from the shop where you purchased the product.

If possible, use the original packaging when returning the product for service. Include a dated description of its use and the fault, together with your full address and telephone number.

Recycling (European Union)​

Electrical equipment bearing the crossed-out bin symbol must not be disposed of in normal household waste. Instead, it must be taken to a specialised collection and recycling facility. In EU (European Union) countries, electrical equipment must not be disposed of in normal household waste (WEEE - Waste of Electrical and Electronic Equipment, Directive 2012/19/EU). You can take unwanted equipment to your nearest collection or recycling centre. The equipment will then be disposed of or recycled safely, free of charge. By handing in your unwanted equipment, you can make an important contribution to protecting the environment.

EU Declaration of Conformity​

Dongguan Freewing Electronic Technology Co., Ltd. hereby declares that the model Freewing F-16 Fighting Falcon 680 mm – 6S and the equipment supplied with it comply with the applicable European Union requirements. The full text of the EU Declaration of Conformity is available at www.kavanrc.com/doc.

Manuel complet: https://wiki.kavanrc.com/fr/distribution/freewing/f16-fighting-falcon-680-6s · #FWFJ11113P