KAVAN Savage Mini - Instruction manual

Introduction

Congratulation on your purchase of the high performance 3D aerobatic SAVAGE Mini model! You are about to start the assembly of a model manufactured from virtually unbreakable EPP (extruded polypropylene) foam powered by a mighty brushless motor and lightweight LiPo battery. Everybody who has already mastered flying a "full house" trainer - with aileron, elevator, rudder, and throttle control - will enjoy this bad boy.

Before you start

1. If you are not an experienced RC pilot, plan to have a fully competent pilot check your completed model and help you with your first flights. Even though we have tried to provide you with a thorough instruction manual, RC models are rather complicated and an experienced modeller can quickly check over your model to make sure your first flights are successful.
2. Please assemble your model exactly according to these instructions. Do not attempt to modify or change your model in any way as doing so may adversely change its flying characteristics.
3. Before you begin, please check the entire contents of this kit to make sure that no parts are missing or damaged. This will also help you to become familiar with each component of your plane. If you find that any of the parts are either missing or damaged, please contact your dealer immediately for replacement.
4. Trial fit each part before glueing it in place. Make sure you are using the correct part and that it fits well before assembling. No amount of glue can make up for a poorly fitting part.
5. The manual contains a drawing showing the default position of the Centre of Gravity (CG) and recommended control surface throws. Please note it is essential to keep the recommended CG position for the first flight otherwise the model could be unstable, hard to control or even unable to fly at all! Later you can fine-tune the CG position to suit your flying style and skills.

Note: Your dealer cannot accept kits for return if construction has begun.

Safety precautions and warnings

• An RC aeroplane is not a toy! If misused, it can cause serious bodily harm and damage to property. Fly only in a safe place following all instructions and recommendations in this manual. Beware of the propeller! Keep loose items that can get entangled in the propeller away from the spinning propeller, including loose clothing, or other objects such as pencils and screwdrivers. Ensure that your and other people’s hands and faces are kept away from the rotating propeller.
• As the user of this product, you are solely responsible for operating it in a manner that does not endanger yourself and others or result in damage to the product or the property of others. This model is controlled by a radio signal, that is subject to interference from many sources outside your control. This interference can cause momentary loss of control, so it is advisable to always keep a safe distance in all directions around your model, as this margin will help to avoid collisions or injury.
• Never operate your model with low transmitter batteries.
• Always operate your model in an open area away from power lines, cars, traffic, or people. Avoid operating your model in populated areas where injury or damage can occur.
• Carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable batteries, etc.) which you use.
• Keep all chemicals, small parts and anything electrical out of the reach of children.
• Moisture causes damage to electronics. Avoid water exposure to all equipment not specifically designed and protected for this purpose.
• The model is mostly made of plastics – it is not fireproof. It may not be exposed to higher temperatures otherwise severe distortion of the foam airframe or other damage may occur.

Specification

Wingspan	1000 mm
Length	1020 mm
All–up weight	ca 500 g

You will also need

• At least four channel RC set, a power unit with 3S LiPo flight pack and servos - refer to "Recommended power systems and servos".
• Regular modeller’s tools: modeller’s knife, screwdrivers, pliers, electric drill with drill bits (3.0 mm), No. 180–360 sandpaper, etc.
• Glue: medium and thin CA glue, accelerator for CA glue, hot melt glue.

Recommended power systems and servos

• Sunday 3D: For 3D aerobatic beginners and Sunday flyers.)
• 3D: For everybody who likes it hot and 3D.

Note: 20–30A ESC with a good linear BEC should be OK if you are using analog servos. However, if you are using high torque & speed digital servos, you should go for an ESC featuring powerful switching SBEC.

	Sunday 3D	3D
Motor	KAVAN C2830–1300	KAVAN PRO 2830–1300
Propeller	APC 9×4.7"SF	APC 10×4.7"SF
ESC	KAVAN R–30B	KAVAN PRO–30SB
Battery	KAVAN LiPo 11.1V 1300mAh 40/80C	KAVAN LiPo 11.1V 1300mAh 40/80C
Servos	KAVAN GO–13MG, Hitec HS- -65MG, HS–70MG	KAVAN GO–1013MG, Hitec HS–5065MG, HS–5070MH