Programmierkarte KAVAN PRO - Bedienungsanleitung

Other languages:

Deutsch
English
čeština

Einführung

Programmier-Karte für KAVAN PRO/Plus Elektronische Brushless Regler

KAVAN PRO Programmier-Karte für Elektronische Regler ist leicht zu verwenden und bequem mitzunehmen. Alle programmierbaren Funktionen sind in der Programmier-Karte aufgelistet.

Technische Daten


Eingangs Spannung	4,8 – 8,4 Volt DC (BEC oder SBEC des Reglers oder 4–5 zellige Empfängerbatterie NiCd/NiMH oder 2S LiPo/Li-ion/LiFe)
Abmessungen	88×58×14 mm
Gewicht	40 g

Funktionen

Anschluss-reihenfolge

Achtung: Der Regler MUSS(!) an der Programmier-Karte angeschlossen werden, BEVOR der Akku angeschlossen wird! Andernfalls kann Ihr Regler nicht mit der Programm karte „verbunden“ werden.

Für den KAVAN PRO Regler (mit dem Programmierkabel, das eine Ausgangsspannung von 5,2–7,4V hat): Stecken Sie das Programmierkabel in den mit "(-)(+)(⎍)" gekennzeichneten Anschluss Ihrer LED-Programmkarte.

Hinweis: Das Programmierkabel ist das „kürzere“ Kabel mit einem JR-Stecker an Ihrem KAVAN PRO Regler.

Making the programming card work

After connecting everything, please connect a battery to your ESC and turn it on. A few seconds later, the KAVAN PRO Programming Card will display the current settings in your ESC. If the programming card doesn’t display anything, then please check if the programming cable and the wire (on UBEC/the extra battery) for powering the KAVAN PRO Programming Card have been reversely plugged in. After confirming all the connections (are correct), disconnect the battery, and 2 seconds later re-connect it to your ESC to see if any information is displayed on the KAVAN PRO Programming Card.

Warning: It often takes a few seconds before the KAVAN PRO Programming Card displays "digits/information".

Programming your KAVAN PRO ESC

ITEM Button: pressing the ITEM button selects the programmable item(s) you want to adjust/check; the corresponding (item) number of each item will be displayed on the left LED display.

VALUE Button: after selecting a programmable item, the corresponding parameter stored in your ESC will be displayed on the right LED display. Pressing the VALUE button adjusts the parameter values.

OK Button: press the OK button after you adjust all the parameters (you want to adjust). A Red "——" will show up on the right LED display for about 1 or 2 seconds to indicate it’s transferring the new parameter values to your ESC. The red "——" will disappear when the ESC saves all the parameter values.

RESET Button: pressing the RESET button resets your ESC to the factory settings.

Attention: You need to power your ESC off and then on after adjusting the parameters, otherwise the new parameters won’t take effect.

Note: Find the detailed description of all programmable functions in the instruction manual supplied with your KAVAN PRO or Plus ESC.

Safety precautions

Do not install the propeller (fixed-wing) or drive pinion (helicopter) on the motor when you test the ESC and motor for the first time to verify the correct settings on your radio. Install your propeller (plane) or pinion (heli) only after confirming the settings on your radio are correct.
Never use ruptured or punctured battery cells.
Never short-circuit battery or motor terminals.
Always use proper insulation material for cable insulation.
Always use proper cable connectors.
Incorrect battery polarity will damage the card and ESC and void the warranty.
Use only batteries supported by the card and ESC and ensure the correct polarity before connecting.
Handle your model with extreme care once the battery pack is connected and keep away from the propeller at all times. Never stand in line or directly in front of any rotating parts.
Do not immerse the card under water, do not allow it to get wet while powered up.

Recycling and waste disposal note (European Union)

Electrical equipment marked with the crossed-out waste bin symbol must not be discarded in the domestic waste; it should be disposed of via the appropriate specialised disposal system. In the countries of the EU (European Union) electrical devices must not be discarded via the normal domestic waste system (WEEE - Waste of Electrical and Electronic Equipment, Directive 2012/19/EU). You can take your unwanted equipment to your nearest public collection point or recycling centre, where it will be disposed of in the proper manner at no charge to you. By disposing of your old equipment in a responsible manner you make an important contribution to the safeguarding of the environment.

EU declaration of conformity (European Union)

Hereby, KAVAN Europe s.r.o. declares that the KAVAN Pro Programming Card is in compliance with the essential requirements as laid down in the EU directive(s) concerning electromagnetic compatibility. The full text of the EU Declaration of Conformity is available at www.kavanrc.com/doc/.

Guarantee

The KAVAN Europe s.r.o. products are covered by a guarantee that fulfils the currently valid legal requirements in your country. If you wish to make a claim under guarantee, please contact the retailer from whom you first purchased the equipment. The guarantee does not cover faults which were caused in the following ways: crashes, improper use, incorrect connection, reversed polarity, maintenance work carried out late, incorrectly or not at all, or by unauthorised personnel, use of other than genuine KAVAN Europe s.r.o. accessories, modifications or repairs which were not carried out by KAVAN Europe s.r.o. or an authorised KAVAN Europe s.r.o., accidental or deliberate damage, defects caused by normal wear and tear, operation outside the Specification, or in conjunction with equipment made by other manufacturers. Please be sure to read the appropriate information sheets in the product documentation.