KAVAN Savage MAX - Instruction manual

Introduction

Congratulation on your purchase of the high performance 3D aerobatic SAVAGE MAX model! You are about to start the assembly of a model manufactured from virtually unbreakable EPP (extruded polypropylene) foam powered by a mighty brushless motor and lightweight LiPo battery. Everybody who has already mastered flying a “full house” trainer - with aileron, elevator, rudder, and throttle control - will enjoy this beast!

Before you start

If you are not an experienced RC pilot, plan to have a fully competent pilot check your completed model and help you with your first flights. Even though we have tried to provide you with a thorough instruction manual, RC models are rather complicated and an experienced modeller can quickly check over your model to make sure your first flights are successful.
Please assemble your model exactly according to these instructions. Do not attempt to modify or change your model in any way, as doing so may adversely change its flying characteristics.
Before you begin, please check the entire contents of this kit to make sure that no parts are missing or damaged. This will also help you to become familiar with each component of your plane. If you find that any of the parts are either missing or damaged, please contact your dealer immediately for replacement.
Note: Your dealer cannot accept kits for return if construction has begun.
Trial fit each part before gluing it in place. Make sure you are using the correct part and that it fits well before assembling. No amount of glue can make up for a poor fitting part.
The manual contains a drawing showing the default position of the Centre of Gravity (CG) and recommended control surface throws. Please note it is essential to keep the recommended CG position for the first flight otherwise the model could be unstable, hard to control or even unable to fly at all! Later, you can fine tune the CG position to suit your flying style and skills.

Precautions

This RC model is not a toy. Use it with care and strictly following the instructions in this manual.

Assemble this model following strictly these instructions. DO NOT modify or alter the model. Failure to do so, the warranty will lapse automatically. Follow the instructions in order to obtain a safe and solid model at the end of the assembly.

Children under the age of 14 must operate the model under the supervision of an adult.

Assure that the model is in perfect conditions before every flight, taking care that all the equipment works correctly and that the model is undamaged in its structure.

Fly only in days with light breeze and in a safe place away from any obstacles.

Safety precautions and warnings

An RC aeroplane is not a toy! If misused, it can cause serious bodily harm and damage to property. Fly only on a safe place, following all instructions and recommendations in this manual. Beware of the propeller! Keep loose items that can get entangled in the propeller away from the spinning propeller, including loose clothing, or other objects such as pencils and screwdrivers. Ensure that yours and other people’s hands, and face are kept away from the rotating propeller.
As the user of this product, you are solely responsible for operating it in a manner that does not endanger yourself and others or result in damage to the product or the property of others. This model is controlled by a radio signal that is subject to interference from many sources outside your control. This interference can cause momentary loss of control, so it is advisable to always keep a safe distance in all directions around your model, as this margin will help to avoid collisions or injury.
Never operate your model with low transmitter batteries.
Always operate your model in an open area away from power lines, cars, traffic, or people. Avoid operating your model in populated areas where injury or damage can occur.
Carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable batteries, etc.) which you use.
Keep all chemicals, small parts and anything electrical out of the reach of children.
Moisture causes damage to electronics. Avoid water exposure to all equipment not specifically designed and protected for this purpose.
The model is mostly made of plastic - it is not fireproof. It may not be exposed to higher temperatures, otherwise severe distortion of the foam airframe or other damage may occur.

Specification


Wingspan	1080 mm
Length	1200 mm
All-up weight	ca 850 g

You will also need

At least four channel RC set, a power unit with 3–4S LiPo flight pack and servos - refer to "Recommended power systems and servos".
Regular modeller’s tools: modeller’s knife, screwdrivers, pliers, electric drill with drill bits (1.5 mm, 1.6 mm, 2.0 mm, 3.0 mm), No. 180–360 sandpaper, etc.
Glue: medium and thin CA glue, accelerator for CA glue, hot melt glue.

Recommended power systems and servos

Sunday Acro: For aerobatic beginners and Sunday flyers; for everybody who prefers classic pattern aerobatics with a light and virtually unbreakable foam model.
Acro: For sporty flyers preferring pattern aerobatics.
Sunday 3D: For 3D aerobatic beginners and Sunday flyers.
3D: For everybody who likes it hot and 3D.
Note: 40–45A ESC with a good linear BEC should be OK if you are using analogue servos; however, if you are using high torque & speed digital servos, you should go for an ESC featuring powerful switching SBEC.


3S LiPo	Sunday Acro	Acro
Motor	KAVAN C3536–1250	KAVAN PRO 3536–1150
Propeller	APC 10×5"E	APC 10×5"E
ESC	KAVAN R–40B	KAVAN PRO–40SB
Battery	KAVAN LiPo 11.1V 1800mAh 30/60C	KAVAN LiPo 11.1V 1300mAh 40/80C
Servos	KAVAN GO–13MG, Hitec HS- -65MG, HS–70MG	KAVAN GO–1013MG, Hitec HS–5065MG, HS–5070MH

3S LiPo	Sunday 3D	3D
Motor	KAVAN C3536–1000	KAVAN PRO 3536–1000
Propeller	APC 11×4.7"SF	APC 11×4.7"SF
ESC	KAVAN R–40B	KAVAN PRO–40SB
Battery	KAVAN LiPo 11.1V 1800mAh 40/80C	KAVAN LiPo 11.1V 1300mAh 40/80C
Servos	KAVAN GO–13MG, Hitec HS- -65MG, HS–70MG	KAVAN GO–1013MG, Hitec HS–5065MG, HS–5070MH