Skip to main content

Freewing A-10 Thunderbolt II V3 1270 mm – Instruction manual

Freewing A10 64 V3 PNP 6S
FWFJ11711P

Freewing A10 64 V3 PNP 6S

Introduction​

The A-10 Thunderbolt II V3 is a factory-built EPO radio-controlled aircraft supplied in PNP configuration. The airframe requires final assembly, a compatible radio system and the flight battery specified below. Complete the mechanical, radio and balance checks before flying.

Safety notes and warnings​

Danger

This model is not a toy. Incorrect assembly or operation can cause serious injury. It is intended for experienced RC pilots; inexperienced users need competent assistance. For ages 14 and above; anyone under 14 may operate it only under an adult’s instruction and supervision. Read and retain the complete instructions, including those supplied with the radio, battery, charger, ESC and any gyro.

  • Keep hands, hair, clothing and loose objects away from the EDF intakes, rotors and exhausts. A fan can draw in objects and eject debris.
  • Keep the flight battery disconnected during assembly, transport and maintenance. Connect it only when the model is secure and the propulsion area is clear. Treat the motor as live whenever power is connected.
  • Fly in an unobstructed area clear of people, animals, roads, power lines and buildings. Maintain a safe distance and follow the applicable model-flying rules at your site.
  • Do not fly in rain, poor visibility or unsuitable wind, or with a damaged airframe, weak transmitter battery or unreliable radio link.
  • Use only a compatible LiPo balance charger with the correct cell count and charging settings. Supervise charging on a non-flammable surface. Do not use damaged, swollen or overheated batteries.
  • Keep water, solvents and excessive heat away from the model and electronics. Do not leave the foam airframe or batteries in a hot vehicle or direct heat.

Keep a 2 m clear area around stored flight batteries, free of combustible and explosive materials. Take damaged or exhausted batteries to a suitable battery collection facility. Collect waste at the flying site; do not discard or burn it. Never try to catch the aircraft in flight or during landing—wait until it has stopped and the propulsion is safe.

Features​

  • Painted EPO airframe with factory-installed propulsion and servos.
  • 2× Ø64 mm EDF, 12-blade rotor.
  • Electric retractable landing gear.
  • Working flaps.
  • Installed LED lighting.

Technical specifications​

ParameterValue
Wingspan1270 mm
Length1143 mm
Weight2212 g (excluding drive battery); also excludes scale missiles
AirframeEPO
Propulsion2× Ø64 mm EDF, 12-blade rotor
Brushless motor2× 2840-2200 KV
ESC2× 50 A
Installed servos10
Landing gearElectric retracts
Flight battery, not included6S 4000–5000 mAh LiPo
Radio system, not includedAt least 6 channels for the basic arrangement; additional functions may require more channels
Battery compartment230×63×68 mm
Battery discharge ratingAt least 40C
UBEC7 A

Package contents​

Painted fuselage, wing and tail/control-surface assemblies; installed brushless propulsion, ESC and servos; linkages, specified joiners and assembly hardware; the landing gear and scale fittings supplied for this version. The transmitter, receiver, flight battery and charger are not included. Check every part against the supplied packing list before beginning; contact the supplier if anything is missing or damaged.

Required equipment​

  • A compatible transmitter and receiver with at least 6 channels for the basic functions. Allow extra channels where independent surfaces, thrust vectoring, gyro controls, wing sweep or reverse are specified.
  • A suitable flight battery: 6S 4000–5000 mAh LiPo. Check its dimensions, mass, connector and cell count against the supplied power system and CG before use.
  • A LiPo balance charger suitable for the selected battery and a charged transmitter battery.
  • Suitable screwdrivers and hex drivers, pliers, a ruler/control-throw gauge, a balance stand and a padded model support.
  • EPO-compatible adhesive for the joints specified in the assembly instructions. Test compatibility first; allow the adhesive to cure fully. Use threadlocker only where specified for metal-to-metal fasteners and keep it away from plastic and foam.

Main section​

Preparation​

Danger

Leave the flight battery disconnected. Remove propellers from propeller-driven models. On an EDF model, isolate the motor connection for radio/servo work where accessible, insulating loose connectors individually; disconnect the flight battery before changing any wiring. Restore the original motor connections only for controlled propulsion checks.

  1. Inspect the foam, hinges, joiners, horns, motor mounts and installed wiring for transport damage. Identify left/right parts and the correct fasteners.
  2. Trial fit the assemblies before applying adhesive. Do not force a joint or use glue to compensate for an incorrectly fitted part.
  3. Keep servo and lighting plugs accessible while joining assemblies. Route cables through their channels and protect them from screw tips, moving linkages and landing-gear mechanisms.
  4. Use only the screws specified for each location. Tighten securely without crushing foam or stripping plastic threads.

Assembly​

Tail assembly​

1. Route the fin leads​
Routing the fin leads through the horizontal tail

Route the fin-servo and formation-light leads through the channels in the horizontal tail. Use the supplied pull wire.

2. Secure the fins​
Fin attachment with four M3×7 mm screws

Fit both fins and secure them with 4× M3×7 mm screws in total. Keep the leads clear of the joints.

3. Connect the fin leads​
Formation-light and rudder-servo sockets on the horizontal-tail board

Connect the formation-light and rudder leads to their corresponding sockets on the horizontal-tail control board. Observe the connector polarity.

  • 1: Formation-light connection.
  • 2: Rudder-servo connection.
4. Install the complete horizontal tail​
Horizontal-tail installation and fuselage ribbon-cable socket

Connect the fuselage ribbon cable to socket 3 on the horizontal-tail board. Fit the complete tail assembly and secure it with 4× M3×7 mm screws. Keep all cables clear of the joints.

Motor nacelle​

1. Match the motor connectors​
Numbered motor connectors and matching ESC leads

Match each motor connector to the ESC lead with the same heat-shrink colour. Connect matching numbers; do not swap the connections.

  • 1: Yellow.
  • 2: Black.
  • 3: Red.
  • 4: Motor connectors.
  • 5: ESC leads.
2. Seat the nacelle​
Seating the motor nacelle on the fuselage

Seat the nacelle without pinching the motor or ESC leads. Keep all wiring clear of the joint.

3. Check the left and right wiring​
Separate wiring for the left and right EDF units

Keep the left ESC connected to the left motor and the right ESC connected to the right motor.

4. Secure the nacelle​
Nacelle attachment with four M3×7 mm screws

Secure the nacelle with 4× M3×7 mm screws. Do not pinch the wiring.

QUICK II wing attachment​

1. Identify the unlocked state​
QUICK II latches with their buttons raised

Press the QUICK II latch fully and release it. A raised button indicates an unlocked latch (1).

2. Identify the locked state​
QUICK II latches with their buttons held down

Press the latch again until it remains down. A button that stays down indicates a locked latch (2). Unlock all four latches before fitting the wings.

3. Prepare the carbon joiners​
Two carbon joiners and their conical plastic end pieces

Glue the Ø8 mm conical plastic end pieces onto both Ø8×390 mm carbon joiners. Allow the adhesive to cure.

4. Insert the joiners​
Carbon joiner positions through the fuselage

Insert both carbon joiners through the fuselage in their illustrated positions.

5. Fit the wing halves​
Wing halves sliding onto the joiners with the latches unlocked

Keep all four QUICK II latches unlocked (1). Slide the wing halves onto the joiners and fully into place, connecting their leads.

6. Lock the wings​
Pressing all four QUICK II latches to secure the wings

Press all four QUICK II latches until they remain down. Gently pull each wing outwards to confirm engagement before flight.

Scale accessories​

Scale stores​
Locations of the LAU-131, AGM-65, AN/ALQ-131 and Mk. 84 scale stores

Fit the slide-mounted stores to their matching rails in the illustrated positions. The designations identify the LAU-131 rocket pods, AGM-65 missiles, AN/ALQ-131 pod and Mk. 84 bombs.

1. Fit the first accessory​
Position and fitting direction of the first scale accessory

Fit the accessory in the illustrated position.

2. Fit the second accessory​
Second scale accessory secured with one M3×7 mm screw

Fit the accessory in the illustrated position and secure it with 1× M3×7 mm screw.

3. Fit the third accessory​
Third scale accessory secured with one M3×7 mm screw

Fit the accessory in the illustrated position and secure it with 1× M3×7 mm screw.

4. Fit the fourth accessory​
Position and fitting direction of the fourth scale accessory

Fit the accessory in the illustrated position.

Remove vulnerable accessories for transport.

Receiver installation and radio setup​

  1. Select the correct aircraft memory and label it with the model/version. Keep throttle at its minimum position and enable throttle cut. Bind the receiver following the binding procedure for the radio system with propulsion disabled.
  2. Connect each labelled control lead to its corresponding receiver or control-board function. Follow the board’s signal, positive and negative markings; do not assume every transmitter uses the same channel numbering. Retain the supplied BEC/UBEC wiring.
  3. Secure the receiver and any extensions. Follow the receiver’s antenna-placement requirements and keep antennas clear of power wiring, carbon reinforcement and moving parts.
  4. Centre the servos and set the mechanical neutrals described below before adjusting travel or mixes. Ensure clevises are fully engaged and fit their retaining sleeves; press ball links completely onto their balls.
  5. Program the required functions, control rates and failsafe. Set failsafe to stop the motor and verify its actual operation with propulsion disabled. Recheck after changing the receiver, transmitter memory or control-board configuration.

Elevator neutral​

The 4 mm elevator-neutral reference, plastic-to-foam joint and plastic part

Set both elevators to the same neutral position. Set a 4 mm offset between the tail trailing-edge reference and the line at the fin/plastic-to-foam joint, as illustrated.

  • 1: Plastic-to-foam joint.
  • 2: Plastic part.

Flap compensation and expo​

Set flap-to-elevator compensation to 0.8 mm down elevator with 10 mm flap and 1.0 mm down elevator with 15 mm flap. Verify the direction and recheck it in flight at a safe height.

Use high rates with suitable expo for the maiden flight. Suggested expo is 30 % for aileron/rudder and 40 % for elevator: −30/−40 % on Futaba, +30/+40 % on Spektrum. Other transmitters can use the opposite sign convention; select the setting that softens response around centre.

Flight battery and power-system check​

Use 6S 4000–5000 mAh LiPo. Follow the discharge requirement in the specification table where provided, and the requirements of the supplied power system. Fit the battery without forcing the canopy or crushing wires. Use the retaining straps and a non-slip support, and adjust its position for the specified CG. Leave it disconnected while balancing and completing the installation.

  1. Check polarity and connector security with the battery disconnected. Make sure cooling inlets and outlets are clear.
  2. Switch on the transmitter with the correct model memory, throttle at minimum and throttle cut enabled. Secure the aircraft and keep everyone clear before connecting the flight battery.
  3. Wait for the ESC and any gyro to initialise. Stop if there is an unexpected tone, error indication, servo movement or motor start.
  4. Calibrate the throttle range only by the instructions for the installed ESC. Repeat when required after changing the radio system; do not use an unverified generic high-throttle startup procedure.
  5. With propulsion correctly assembled, check rotation and response in a clear area. Stop immediately if there is vibration, rubbing or an abnormal noise. Disconnect the battery before investigating.

Check both EDF units. They must start and accelerate consistently; investigate any difference before flying.

Linkage reference​

Use the dimensions, measurement endpoints and attachment arrangements shown below. The highlighted numbers identify the specified servo-arm and control-horn holes; changing a hole changes both travel and load. Secure the retainers and check full movement without binding.

Flap​

Flap pushrod length and attachment arrangement

Length: 73 mm. Rod diameter: Ø1.2 mm. Use the illustrated measurement endpoints and attachment arrangement.

Aileron​

Aileron pushrod length and attachment arrangement

Length: 60 mm. Rod diameter: Ø1.2 mm. Use the illustrated measurement endpoints and attachment arrangement.

Elevator​

Elevator pushrod length and attachment arrangement

Length: 60 mm. Rod diameter: Ø1.2 mm. Use the illustrated measurement endpoints and attachment arrangement.

Rudder​

Rudder pushrod length and attachment arrangement

Length: 49 mm. Rod diameter: Ø1.2 mm. Use the illustrated measurement endpoints and attachment arrangement.

Nose-wheel steering​

Nose-wheel steering pushrod length and attachment arrangement

Length: 55 mm. Rod diameter: Ø1.5 mm. Use the illustrated measurement endpoints and attachment arrangement.

Nose door​

Nose door pushrod length and attachment arrangement

Length: 33 mm. Rod diameter: Ø1.2 mm. Use the illustrated measurement endpoints and attachment arrangement.

Nose following door​

Nose following door pushrod length and attachment arrangement

Length: 24 mm. Rod diameter: Ø1.2 mm. Use the illustrated measurement endpoints and attachment arrangement.

Rear following door​

Rear following door pushrod length and attachment arrangement

Length: 39 mm. Rod diameter: Ø0.6 mm. Use the illustrated measurement endpoints and attachment arrangement.

Pre-flight preparation​

Centre of gravity​

Centre-of-gravity datum and balance marks

Balance at the moulded CG marks on the underside of the model for the maiden flight; the reference dimension is 74 mm. Use the exact datum in the drawing, rather than measuring from an arbitrary point on the swept leading edge. After successful test flights, adjust the CG only within ±5 mm of this position.

Check with the model completely assembled, including the selected battery, canopy and the accessories that will be flown. Keep power disconnected. Move and secure the battery to achieve the specified balance. Use the exact datum and aircraft configuration in the drawing.

Attention

Do not fly with the CG outside the specified position/range. A battery that fits physically may still prevent correct balance. Recheck after changing a battery, accessories, repairs or equipment. If the CG measurement datum or its applicability to the supplied version is uncertain, obtain confirmation before flight.

Control throws​

Ailerons​

Aileron measuring point and H1/H2 throw directions

Measure closest to the fuselage, from neutral in each direction.

Flaps​

Flap measuring point and downward throw

Measure closest to the fuselage, down from neutral.

Elevator​

Elevator measuring point and H1/H2 throw directions

Measure closest to the fuselage, from the specified neutral position in each direction.

Rudder​

Rudder measuring point and H1/H2 throw directions

Measure at the bottom of the rudder, from neutral in each direction.

H1/H2 denote the two measured directions. A value given for each direction is not the total end-to-end travel. Treat transmitter percentages as reference settings; adjust the radio to reproduce the specified measured movement.

ControlLow rateHigh rate
Aileron, each direction21 mm / 100 %24 mm / 120 %
Elevator, each direction11 mm / 80 %15 mm / 100 %
Rudder, each direction13 mm / 80 %16 mm / 100 %
Flaps, down10 mm15 mm

Set the neutrals and any specified flap compensation in Receiver installation and radio setup before checking these throws.

Control-direction check​

Disable propulsion as described in Preparation before powering the radio for these checks. Check directions from behind the aircraft, with the model facing away. Test one function at a time, then combined inputs at the stick corners. Do not fly if any movement disagrees with the diagrams.

Aileron — stick left​

Left roll: left aileron up and right aileron down

The left aileron trailing edge moves up and the right aileron trailing edge moves down.

Aileron — stick right​

Right roll: right aileron up and left aileron down

The right aileron trailing edge moves up and the left aileron trailing edge moves down.

Elevator — stick back​

Pitch-up command: both elevator trailing edges move up

Both elevator trailing edges move up for a pitch-up command. Check both halves and the specified neutral offset.

Elevator — stick forward​

Pitch-down command: both elevator trailing edges move down

Both elevator trailing edges move down for a pitch-down command.

Rudder — stick left​

Left yaw: both rudder trailing edges move left

Both rudder trailing edges move left. Check that the nose-wheel steering follows the commanded turn.

Rudder — stick right​

Right yaw: both rudder trailing edges move right

Both rudder trailing edges move right. Check that the nose-wheel steering follows the commanded turn.

Flaps down​

Both flaps lowered together

Both flaps lower together to the selected setting and return fully to neutral. Verify the specified elevator compensation.

Retracts​

Support the model with the wheels clear. Check that the gear and doors complete their intended sequence without binding and that the extended gear is secure.

Pre-flight checks​

  1. Confirm that all adhesives are cured, fasteners are secure and the wing/tail attachments are locked. Pull-check removable wings and inspect hinges, horns, ball links and clevis retainers.
  2. Confirm the CG, neutral positions, control throws, correct model memory and directions. Check every flight mode and any gyro, vectoring, flap, sweep or retract function fitted.
  3. Carry out a range test and failsafe test following the radio instructions, with propulsion disabled. Do not fly if the radio link or failsafe is unreliable.
  4. Check that batteries are charged, securely retained and undamaged. Confirm connector polarity, canopy retention and that no cable can reach the propulsion or moving mechanisms.
  5. Inspect the propulsion for damage or foreign objects. Verify that the cooling path is open and that a controlled motor check produces no abnormal vibration.
  6. Check the flying area, weather, runway/landing area and the position of other people. Have an experienced pilot check the initial setup.

Maiden flight and landing​

Make the maiden flight in calm, suitable conditions at an established model-flying site. Use the initial CG and high-rate throws specified for this model. Plan a short flight with reserve battery capacity.

High rates are recommended for the maiden flight to keep the full specified control travel available if unexpected trim or handling problems require larger corrections. Program a comfortable amount of exponential (expo) to soften the response around stick centre while retaining full control-surface travel at the stick limits. Where expo values are given in this manual, use them as a starting point and check the sign convention on your transmitter. High rates and expo do not compensate for an incorrect CG or mechanical setup; complete all balance and control checks before flying.

Climb to a safe height before trimming or testing a different rate or flap setting. Make one adjustment at a time.

Use a clear runway suited to the model and its wheels. Take off into wind, keep the wings level and avoid pulling into a steep climb before the model has flying speed. Check any flap compensation at safe altitude before using it on approach. Land into wind and reduce throttle before touchdown.

Shutdown​

  1. Stop the motor, enable throttle cut and keep the transmitter on.
  2. Disconnect all flight batteries before switching off the transmitter or retrieving the model for maintenance.
  3. Remove the battery, allow the battery and power system to cool, and inspect the airframe and propulsion.
  4. Store LiPo packs at the storage state specified for the battery. Do not leave a battery connected inside the model.

Appendix​

Maintenance and transport​

Inspect the model after every flight and particularly after a hard landing. Check foam joints, joiners, hinges, control horns, retaining screws, linkages, retract mounts and electrical connectors. Replace damaged propulsion parts; do not try to fly out a vibration. Repairs must restore alignment, strength and free control movement. Repeat the balance, control and range checks after repairs.

Clean with a soft cloth and materials compatible with the foam and paint. Keep moisture out of electronics and bearings. Remove fragile scale fittings for transport, protect the controls from pressure and support the airframe without distorting it. Disconnect batteries before removing wings or unplugging connectors.

Installed-servo reference​

Determine positive/reverse servo rotation by watching the servo arm as the input changes from 1000 μs to 2000 μs: clockwise is positive, anticlockwise is reverse. This describes servo hardware, not a transmitter reverse setting. Match size, travel, gear type, direction, voltage compatibility and cable length when selecting a replacement.

FunctionServoRotationCable length (mm)
Nose-wheel steering9 g, hybrid gearsPositive500
Nose door9 g, plastic gearsPositive500
Left/right aileron9 g, hybrid gearsPositive400
Left flap9 g, hybrid gearsPositive200
Right flap9 g, hybrid gearsReverse200
Left elevator9 g, hybrid gearsPositive100
Right elevator9 g, hybrid gearsReverse100
Left/right rudder9 g, hybrid gearsPositive300

Troubleshooting​

SymptomChecks before further operation
Motor does not armDisconnect power. Check the correct model memory, receiver binding, throttle minimum/trim, throttle cut, battery condition and connector polarity. If fitted, check that reverse is in the required startup position. Consult the installed ESC’s error indications.
Motor starts unexpectedly or runs in the wrong directionDisconnect power immediately. Check throttle direction, failsafe and wiring with propulsion disabled. Do not change motor connections while the battery is attached.
Surface moves incorrectly or bindsCheck the labelled plugs, transmitter mixes/reversing, servo-arm/horn holes and linkage geometry. Check the entire range and combined commands; repeat gyro direction checks.
Vibration or loss of powerStop and disconnect the battery. Inspect the rotor/propeller, fasteners, bearings, intake and cooling path. Check the battery within its specified operating limits and replace damaged components.
Pitch changes when flaps deployRecheck CG, neutral positions, symmetric flap travel and the specified elevator mix. Adjust only after a safe-height test; do not conceal an incorrect mechanical setup with excessive trim.
Gear or doors fail to complete their sequenceWith power disconnected, inspect wiring and obstructions. Support the model for a controlled test and keep fingers clear. Do not repeatedly drive a jammed mechanism.

Warranty and post-warranty service​

All Freewing products are covered by a 2-year warranty covering all manufacturing defects and faults. When making a claim within the warranty period, please always present a copy of the proof of purchase with the product and provide the service personnel with as detailed and complete information as possible about the defect found, your usage and other information that will facilitate the assessment of the claim and speed up its settlement. Please make your claim at the shop where you purchased the product.

This warranty certificate entitles you to a free warranty repair of the product supplied by KAVAN Europe s.r.o. within a period of 24 months. The warranty does not cover natural wear and tear due to normal use, as this is a product for modelling use, where the individual parts operate under much higher loads than normal toys are subjected to.

The warranty also does not cover any part of the equipment that has been improperly installed, roughly or improperly handled, or damaged in an accident, or any part of the equipment that has been repaired or altered by an unauthorised person (this includes the application of any waterproof sprays/coatings by the user). Like other fine electronics products, do not expose this equipment to high temperatures, low temperatures, moisture, dusty environments, violent mechanical shocks and impacts. Do not leave it in direct sunlight for extended periods of time.

Improper installation includes inadequate mounting, mechanical strain on cables and insufficient cooling.

Please claim warranty repairs from the shop where you purchased the product.

If possible, use the original packaging when returning the product for service. Include a dated description of its use and the fault, together with your full address and telephone number.

Recycling (European Union)​

Electrical equipment bearing the crossed-out bin symbol must not be disposed of in normal household waste. Instead, it must be taken to a specialised collection and recycling facility. In EU (European Union) countries, electrical equipment must not be disposed of in normal household waste (WEEE - Waste of Electrical and Electronic Equipment, Directive 2012/19/EU). You can take unwanted equipment to your nearest collection or recycling centre. The equipment will then be disposed of or recycled safely, free of charge. By handing in your unwanted equipment, you can make an important contribution to protecting the environment.

EU Declaration of Conformity​

Dongguan Freewing Electronic Technology Co., Ltd. hereby declares that the model Freewing A-10 Thunderbolt II V3 1270 mm and the equipment supplied with it comply with the applicable European Union requirements. The full text of the EU Declaration of Conformity is available at www.kavanrc.com/doc.

Full manual: https://wiki.kavanrc.com/distribution/freewing/a10-thunderbolt-v3-1270 · #FWFJ11711P