KAVAN Strike DLG - Instruction manual/cs

Úvod

KAV02.8024 KAVAN Strike DLG

Bezpečnostní opatření

Tento RC model není hračka. Používejte jej opatrně a důsledně dodržujte pokyny uvedené v tomto návodu.

Model sestavte přesně podle tohoto návodu. Model NEMODIFIKUJTE ani neupravujte. V opačném případě záruka automaticky zaniká. Postupujte podle pokynů, abyste na konci montáže získali bezpečný a pevný model.

Děti mladší 14 let musí model ovládat pod dohledem dospělé osoby. Před každým letem se ujistěte, že je model v bezvadném stavu. Dbejte na to, aby veškeré vybavení fungovalo správně a aby model neměl poškozenou konstrukci.

Létejte pouze ve dnech se slabým větrem a na bezpečném místě mimo dosah překážek.

Technické údaje

Rozpětí	1 498 mm
Délka	1 070 mm
Letová hmotnost	230–260 g
Profil	YA 0801
Poloha těžiště	74–78 mm
Ovládané funkce	Křidélka, směrovka, výškovka

Doporučené vybavení

• Serva směrovky a výškovky: KAVAN GO-6MG 2×
• Akumulátor: 1S LiPo 3,7 V 450–500 mAh

Doporučená lepidla

Pokud není výslovně uvedeno jinak, díly lepte středním vteřinovým lepidlem (#KAV56.9952 KAVAN CA Medium). Tuhý potah středu křídla je vhodné lepit voděodolným disperzním lepidlem (alternativně můžete disperzním lepidlem lepit všechny spoje dřevo-dřevo kromě pevnostních) – např. KAV56.9960 KAVAN disperzní lepidlo SUPER. Pevnostní spoje (kořenové části křídla, trupové přepážky atd.) lepte 30minutovým epoxidovým lepidlem (např. KAV56.9967), které má vysokou pevnost a poskytuje dostatek času na přesné slícování dílů.

Nářadí a pomůcky

• Velmi ostrý modelářský nůž s výměnnými čepelemi (např. Excel 16001 s čepelemi č. 11 #KAV66.770)
• Nůžky
• Elektrická vrtačka se sadou vrtáků
• Štípací kleště
• Kleště s plochými tenkými čelistmi
• Šroubováky ploché a křížové
• Žiletková pilka
• Brusný papír 100–120, 180–220, 360–400
• Sada jehlových pilníků
• Páječka s pájkou
• Kolíčky na prádlo, kancelářské nebo truhlářské svorky
• Modelářské špendlíky
• Tyčinka a nádobka na míchání epoxidu
• Maskovací páska, isolepa
• Denaturovaný líh (pro otírání nadbytečného epoxidu)
• Papírový ubrousek nebo čistý hadřík (pro otírání nadbytečného epoxidu)
• Ocelové pravítko
• Pravoúhlý trojúhelník
• Tenká průhledná polyetylénová fólie
• Lihový značkovač s tenkým hrotem
• Modelářská žehlička a popř. horkovzdušná pistole pro potahování nažehlovací fólií
• Lehký tmel na balsu
• Pistole na tavné lepidlo + tavné lepidlo

Upozornění

RC model, který budete stavět a létat, není hračka! Ačkoliv Vám může připadat lehký a pomalý v letu, je schopen při nesprávném zacházení způsobit vážné zranění nebo poškození majetku. Je na Vás a jen na Vás, zda postavíte model správně, správně instalujete RC soupravu a motor a model zalétáte a dále budete létat v souladu s běžnými zvyklostmi a pravidly (a také selským rozumem). Pokud právě začínáte s RC modely, požádejte o radu ve Vašem modelářském obchodu nebo zkušeného modeláře v místním modelářském klubu tak, abyste našli dobrého instruktora.

Před stavbou

Model stavte přesně podle návodu. Neměňte nebo neupravujte model, protože pokud tak učiníte, riskujete, že model může být nebezpečný nebo neovladatelný. Najděte si čas pro stavbu, stavějte vše pevně a spolehlivě. Použijte odpovídající RC soupravu a další vybavení, které je v prvotřídním stavu. Správně instalujte všechny části modelu a přezkoušejte jejich činnost a fungování před prvním a každým dalším letem. Pokud nejste zkušený RC pilot, létejte jen s pomocí zkušeného modeláře.

Pozn.: My, jako výrobce stavebnice Vám můžeme zaručit stavebnici prvotřídní kvality s podrobným návodem, ale letové vlastnosti a výkony závisí výhradně na tom, jak model dokončíte Vy. Protože nemáme žádnou kontrolu nad tím, jak model dokončíte, nemůžeme převzít (a nemůže být ani předpokládána) jakoukoliv odpovědnost za případné škody způsobené nebo související s provozem Vámi dokončeného modelu.

Stavba modelu

Ocasní plochy

• Připravte si a na sucho bez lepení slícujte díly ocasních ploch. Dle potřeby zabruste. (Obr. 1)
• Brusným papírem č. 120 lehce zdrsněte povrch uhlíkové pásnice 3×0,5

mm R3 a nalepte ji středním vteřinovým lepidlem na odtokovou hranu kýlovky R1.

• Do vodorovného stabilizátoru T1 vlepte výztuhu T3 z topolové překližky. Po vytvrzení lepidla výztuhu zabruste do roviny se stabilizátorem.
• Povrch všech dílů ocasních ploch přebruste brusným papírem č. 120 a zaoblete jejich vnější hrany. Náběžnou hranu směrovky a výškovky zabruste do úkosu dle Det. D–D.
• Ocasní plochy dokončíte poté, co na ocasní nosník nalepíte lože ocasních ploch (viz stavba trupu).

Trup

• Připravte si a na sucho bez lepení slícujte díly trupové gondoly. Dle potřeby zabruste. Ujistěte se, že uhlíkový trubkový ocasní nosník F1 je možno snadno, ale těsně zasunout do otvorů v přepážkách F10 a F8.
• Na vnitřní stranu levé bočnice F3L (s velkým výřezem pro poklop F11) přilepte balsovou výztuhu F2L (s výřezem pro západku poklopu F14). Na vnitřní stranu pravé bočnice F3R (bez výřezu pro poklop) přilepte balsovou výztuhu F2R. (Obr. 2)
• Na přední okraj poklopu prostoru pro elektroniku F11 přilepte západku F14 tak, aby zapadala do výřezu ve výztuze bočnice F2L a poklop bylo možno volně zasunout to otvoru v bočnici F3L. Pár magnetů F15 sloužících jako zámek poklopu vlepte 5min epoxidem do otvorů v poklopu F11 a ve výztuze F2L až po potažení trupu, aby se magnety vysokou teplotou neodmagnetovaly. Dávejte pozor na jejich polaritu. Musejí se přitahovat! (Obr. 4+5)
• Do překližkové příčky F9 zespodu epoxidem vlepte hliníkovou matici upevňovacího šroubu křídla M4. Trupové přepážky a příčky nezapomeňte předem zabrousit do úkosu všude, kde je třeba. (Obr. 6+3)
• Trupové přepážky a příčky F10, F9, F8, F6 lepte 30min epoxidem postupně od zadu dopředu nejprve do jedné bočnice a poté přiložte druhou. Gondolu položte na stavební plán chráněný tenkou čirou plastovou fólií a kontrolujte, že je rovná a nezkroucená - dle potřeby ji přišpendlete k pracovní desce do vytvrzení lepidla.
• Poté vlepte přepážku F4, do úkosu předem zabroušenou výplň přídě F5 a příčky F17 a F18.
• Na spodní část trupu epoxidem přilepte desku vlečného háčku F7. (Obr. 7)
• Na úrovni přední přepážky F10 nařízněte (do hloubky cca 0,5–1 mm) obě bočnice a opatrně je nalomte (řez před konečným přebroušením trupu nasyťte vteřinovým lepidlem). Do otvorů v přepážkách F8 a F10 zasuňte ocasní nosník F1 - zatím nelepte.
• Na ocasní nosník F1 nasuňte překližkový kroužek F21 a k němu bodově přilepte obě bočnice (dbejte, aby ocasní nosník bylo stále možné vyjmout). Vlepte díly horního a spodního potahu F20 a F19. (Obr. 8)
• Nalepte spodní potah trupu F16 a horní potah ze tří dílů F13a, F13b a F13C.
• Celou gondolu (s vloženým poklopem F11) na jemno zabruste tak, aby všechny části včetně kroužku F21 plynule navazovaly na trubku ocasního nosníku.

Wing

• The wing is to be built directly on the building plan protected by a thin sheet of clear plastic film. The wing ribs and riblets are supplied with jig tabs on the bottom side to allow building the wing with an under-cambered profile on a flat surface; at the same time producing the washout (the wing trailing edge is higher by 3 mm at the tips than at the root) necessary for a stable flight of the model. DO NOT CUT the mounting jigs; they will be removed only after the entire wing has been built. There is also the rib spacing jig to correctly set the leading edge ends of rib and riblet mounting jigs. (Fig. 12)
• Epoxy together the wing central ribs W5 and W6; insert 3 mm beech dowels into the holes to obtain the correct match.
  Note: Make a left and right pair of assemblies. (Fig. 9)
• Glue the plywood reinforcement plate W39 (for the W64 DLG pin) into the wing tip W35 and then the wing tip to the trailing edge W30 on a flat working surface; glue the W36 and W37 reinforcement plates in place creating a notch for the plywood wing tip spar W38. (Fig. 10 + 11)
• Thread all the wing ribs and riblets W3 to W32 onto the main spar carbon tube W60; use a round file to trim the openings in the ribs to set the ribs at the required angle. Thread the auxiliary carbon rod spar W61 through the respective holes in the W3 to W12 ribs. (Fig. 12)
• Put the main spar with ribs onto the building plan and insert the ends of ribs into the corresponding notches in the trailing edge W44 (W45 for the right-wing half). Insert the front ends of the rib jig tabs into the corresponding notches of the rib spacing jig. Align all the parts to the correct position over the building plan; pin down where necessary and then glue the ribs W4 to W31 to the W60 main spar tube, W61 auxiliary spar and the trailing edge. Epoxy the wing tip spar W38 into the main spar tube and to the wing tip into the notch between the W36 and W37 reinforcement plates. Glue the wing tip to the W32 rib and finally, the W32 rib to the main spar and trailing edge. Glue the balsa gusset W33 between the W32 rib and the W31 riblet.
• Glue the root rib W3 using the root rib dihedral jig in place. (Fig. 13)
• Trim the notches for the leading edge W46 (3 mm beech dowel) in the ribs and riblets as necessary. Glue the leading edge (starting from the wing tip and then rib by rib towards the wing root). (Fig. 14)
• Insert the W47 rear spar and the W48 aileron leading edge into the corresponding notches in ribs W4 to W32. Align them both flush with the upper edge of the ribs but do not glue yet.
• Glue the W51 aileron servo frame together with the W52 upper cover plate between the W12 and W14 ribs from above (the opening in the frame fits KAVAN GO-06MG servos; you might have to trim it if other servos are used). Glue the aileron W62 root and W63 tip ribs in place - to the W48 aileron leading edge and W44(45) trailing edge ONLY. Glue the W50 aileron horn block between the W12 and W14 ribs; flush with the upper edge of the ribs and the W48 aileron leading edge. (Fig. 15+16)
• Glue the W34 reinforcement plate between the W30 and W32 ribs, glue the W40 and W41 reinforcements to the wing tip, and glue the two W49 gussets in place. (Fig. 17)
• Epoxy the plywood wing joiner bay plates W43 into the W3, W4 and W5/W6 ribs - be sure the bay will accommodate the W42 wing joiner nicely. (Fig. 20)
• Thoroughly check the entire wing, you are almost there; the wing sports the required 3 mm washout at the tip due to the rib mounting tabs now. Once satisfied, apply cyano to all joints. Note: The W47 rear spar and the W48 aileron leading edge are supposed to be glued to the ribs ONLY, not to each other!
• Now you can carefully cut the rib jig tabs using a sharp modeller’s knife.
• Soak the W51 aileron servo frame and W52 plate with thin cyano or thinned epoxy from the inside. Glue the W53 bottom aileron servo cover between the W12 and W14 ribs. (Fig. 18)
• Sand the bottom side of all ribs and riblets to shape with No. 120 sandpaper.
• Glue the bottom wing centre 1.5 mm balsa sheeting W57 (with a rectangular opening for the aileron servo cable) and W58 in place; glue the plywood reinforcement plate W54 on the top of W58 along the area of the wing fixing bolt. (Fig. 19+20)
• Thread a thick sewing thread through rectangular openings for the aileron servo cable in the W4 to W12 ribs and W57 bottom sheeting and secure it with pieces of sticky tape - it will help you to navigate the aileron servo cable through later.
• Glue the top wing centre 1.5 mm balsa sheeting W56 and W55 in place. Sand the wing root flush with the W3 rib - the slanted position set with the root rib dihedral jig ensures the correct wing dihedral. (Fig. 21)
• Use a fine razor saw and modeller’s knife blade to cut through the ribs and trailing edge to separate the aileron from the wing. Bevel the aileron leading edge by 30° following the Det. A-A. Finally, sand the entire aileron smooth using No. 180 sandpaper. (Fig. 23+24)
• Assemble the other wing half in the same way.
• Sand both two wing halves with No. 120 sandpaper. Trial fit - no glue yet - the wing halves and the W42 wing joiner; insert the riblets W1 and W2 between the root ribs. Once satisfied with the fit, epoxy the W42 wing joiner, and W1 and W2 riblets to one wing half aligned to match the wing root rib. (Fig. 25)
• Put the wing half with the wing joiner glued in on your workbench (protected by a sheet of plastic film) so the alignment pin of the W1 riblet protrudes over the edge of the table; then epoxy the other wing panel. Be sure the trailing edges of both wing panels match perfectly. Double-check the correct wing halves alignment and let the epoxy set. (Fig. 26)
• Epoxy the wing bolt plate W59 to the top of the wing centre; once the glue has cured drill a 4.2 mm hole for the wing bolt through the W59. (Fig. 26)
• Now it is the time to decide which tip of the wing the discus launch pin is to be glued into - the left tip for a right-handed pilot, the right tip for a left-handed pilot. Laminate a strip of the fibreglass cloth around the hole for the discus launch pin on top and bottom of the wing tip. You can use a special low-viscosity laminating/finishing epoxy or a regular epoxy glue thinned slightly by an epoxy paint/dope thinner. Once the resin has cured, sand the entire wing smooth with No. 180 sandpaper.

Covering

• Thoroughly sand the surface of all parts with No. 360–400 sandpaper and carefully vacuum all the dust (the iron-on film does not stick well to a dusty surface; the dust also contains hard grains released off the sandpaper capable of ruining the smooth coating of your sealing iron quickly).
• Use as light iron-on film, as you can get (transparent KAVAN iron-on film, Oracover®, Oralilight® etc. – not supplied in the kit). Follow the instruction manual supplied with the covering film of your choice please.

Final Assembly

Hinging the Control Surfaces

• Use high-quality hinging tape strips (available in hobby shops) or strips of the same iron-on film you used for the covering. Remember to apply the tape with the control surface deflected to the limit (refer to Det. D-D) to get free movement of the particular control surface.

Fuselage and Tail

• Using a very sharp pointed modeller’s knife, cut the covering film over the opening for the tailplane pylon in the horizontal stabilizer, over slots for the Kevlar® thread in the fin and over control horn slots in the elevator and rudder.
• Use a fine needle file to trim the pre-cut slots for the horizontal tailplane pylon, fin, and elevator and rudder push rod exits in the carbon tube tail boom. Use a fine round needle file to make a groove for the rudder push rod tube in the tailplane pylon F22. (Fig. 27)
• Insert the tailplane pylon F22 into the F1 tail boom - no glue yet. Insert the fin and rudder assembly into the notch at the end of the tail boom and tack glue it to the tail boom. Bind the fin to the tail boom with a Kevlar® thread threaded through the slots in the fin. (Fig. 28)
• Slide the horizontal stabilizer on the F22 tailplane pylon; align it square to the fin and to the longitudinal axis of the tail boom and tack glue it to the pylon. Double-check the correct alignment; once satisfied, apply a generous amount of cyano along all the joints and onto the Kevlar® thread. Insert the elevator and rudder push rod outer tubes into the tail boom. Secure them with a piece of polyurethane foam soaked with epoxy that you will work into the centre of the tail boom with a thin stick. This is great for a precise, pushrod backlash-free elevator and rudder control. (Fig. 29)
• The F12 servo mount supplied in the kit has been tailored for the recommended KAVAN GO-6MG servos. Whatever type of servos you use, always check if the openings don’t need trimming first. We recommend soaking the edges of the servo openings with cyano. Once satisfied, glue the F12 servo mount in place (the servos are to be fitted in the upside-down position). (Fig. 30)
• Thread the protruding ends of the elevator and rudder push rod outer tubes through the holes in the F6 former so the tubes lead directly to the horns of servos in the F12 servo mount. Insert the tail boom into the fuselage - no glue yet. (Fig. 31)
• Attach the wing to the fuselage and secure it with the M4 bolt. Looking from above, front and rear check the fuselage and tail boom are straight and the wing dihedral makes a nice symmetrical "V" in relation to the horizontal stabilizer. Once satisfied cut the push rod outer tubes to the correct length and epoxy thoroughly the tail boom into the fuselage. Double-check the correct alignment before the glue sets.
• Solder the M2 brass threaded couplers on one end of the 0.8mm piano wire push rods. Screw the ball links on and slide the push rods into the respective outer tubes. Secure the ball links to both two servo arms with the M1.6 screws supplied in the kit. Insert the fibreglass control horns into the slots in the elevator and rudder - do not glue yet. Set the servos to the neutral with your radio on; attach the servo arms square to the side of the servo case. Set the elevator and rudder flush with the horizontal stabilizer resp. fin. Mark the correct length of the push rods and bend them to the right angle (you can make a "Z-bend", but the simple L-bend usually works well enough). Insert the L-bends into the holes in the control horns and cyano the horns into the elevator and the rudder in place, set in the neutral position. Finally, secure the servos with drops of hot-melt glue, silicone or MS polymer glue in the servo tray. (Fig 29+32)
• Epoxy the pair of F15 magnets into the F11 hatch and fuselage. Double-check their polarity - they have to cling to each other! For easy removal, apply a strip of folded sticky tape to the rear edge of the hatch. (Fig. 4+5)
• Install your receiver into the fuselage, under the wing. The receiver battery will go into the nose.

Wing

• Thoroughly epoxy the carbon discus-launch pin into the left (for a right-handed pilot) or right (for a left-handed pilot) wing tip. (Fig. 33)
• Remove the covering film over the openings for the aileron servo arms in the W52 top cover plates and in the W53 bottom cover plate. Install aileron servos with arms fitted (set them to neutral with your radio on), aileron horns and linkage the same way you did with the rudder and elevator. Finally, using a piece of sticky or iron-on film seal the opening in the W53 bottom cover plates. (Fig. 34+35)

Tow Hook

• Install the tow hook into one of the pre-drilled holes in the F7 tow hook plate; it should be positioned about 5 mm in front of the centre of gravity. (Fig. 36)

Recommended Control Surface Throw, CG Position

• CG Position: 74–78 mm
• Rudder: ±25 mm
• Elevator: ±10 mm
• Ailerons: 10 mm up, 6 mm down
• Ailerons as the airbrake: 40 ° down
• Discus launch configuration: rudder -1 mm against the direction of the launch (right-handed - rudder 1 mm right), elevator 1 mm down.
  
  Note: Use this configuration for the climbing phase of the discus launch only after the model has been trimmed out properly and you‘ve made yourself familiar with the controls.)
• Airbrake → elevator mix: elevator 2 mm down at full airbrake.

Flying

Be sure you are using fully charged batteries. Now (and before any further flight) check the correct function of the whole radio equipment, motor and moving of control surfaces. Be sure any part of flight equipment cannot move during flight. We strongly recommend making a range check (see your radio instruction manual for details).

The first flight: Wait for a calm day. Fly only on a safe site such as an RC club flying field. Glider will be very happy on your favourite slope on a calm day. The very light lift will allow perfect fine trimming out.

Switch your transmitter and then the receiver on and check all the working systems once more. Facing INTO the wind hold your transmitter in one hand; grip the model in the other hand near the centre of gravity. Hold it at head level and give the model a fairly powerful push exactly into the wind; wings level, nose slightly down. Your model should now glide in a long, flat and straight path, without needing any help from you. Use the controls gently if necessary, and adjust the trim tabs until your STRIKE DLG glides the above-described way. Now check the position of control surfaces; set the length of pushrods to bring back trim tabs on your transmitter to the central position if necessary (we strongly recommend doing it in any way). Check again the gliding of your STRIKE DLG.

Now you are ready to make your first discus launch.

Discus Launch

The discus launch allows your model to reach quite a high altitude without much effort. Like with any "sports performance", it will require some training to do it right. Our step-by-step manual makes it easy. We will describe the procedure for a right-handed pilot; with the launching pin attached to the left wingtip. The "left-handed" procedure is the mirror image.

Position A - Getting ready
Your right index and middle fingers should be wrapped around the launch pin at the left wing tip. Your thumb is to be gently pressed against the leading edge of the wing. Stand with your left shoulder into the wind and the right wing tip pointing at ca 45° angle to the ground.

Position B - The first step
Take a long step with your left foot pulling the STRIKE DLG up and forward with your right arm.

Position C - Rotation
Start rotating to the left keeping the STRIKE DLG flat and your right arm extended.

Position D – Continued rotation
The second half of the rotation - the most important part for a good launch. Do not use too much arm in this section. Just let the swing of your torso speed the STRIKE DLG up.

Position E - Release
By this time in the launch the plane will be trying to climb on its own. Just release your fingers and let the plane fly out of your hand directly into the wind.

Position F – Taking the control
Catch your balance; watch your STRIKE DLG climb whilst getting hold of your radio, ready to control your model. The plane will climb after release – the climb angle should be shallow at first; once you are well acquainted with the discus launch you can use more force and increase the launch angle to 60–80 degrees. When completely familiar and comfortable you can add two quick steps before starting the turning sequence, to get some extra speed and energy.

When the plane has slowed almost to the point of stopping push full down elevator to achieve level flight. When this is done at the right moment the plane will go into horizontal flight with just enough airspeed to maintain a gentle glide. If it is done too early the plane will pitch up her nose dangerously after a short dive. If it is done too late the plane will stall.

Go catch some thermals and enjoy your new STRIKE DLG.

Parts list

Main parts
Part	Quantity	Building plan no.	Material
Building Plan 1:1	1
Instruction Manual	1
Sheet of Stickers	1
Pushrod set	2		Plastic tube + 0.8mm piano wire
Tail boom	1	F1	Carbon tube Ø7/6 mm
Rib Spacing Jig	1		Balsa 1.5 mm
Bag no. 1 - small parts
Tow hook	1		Metal
Magnet Ø3 mm	2	F15	Neodymium
Wing Bolt M4	1		Nylon
Captive nut M4	1		Aluminium
Rudder Horn	4		Fibreglass 1.5 mm
Ball link short M2	4		Balsa 1.5 mm
Threaded coupler M2/0.8mm	2		Brass
Rudder and elevator servo tray	1	F12	Balsa 4 mm
Carbon pin	1		Ø5 mm
Fibreglass cloth	1		110 g/m²
Kevlar ® Thread	1
Quicklink	2
Quicklink pin	2
Aileron push rod	2		Carbon rod Ø2 mm
Bag no. 2
Nose block	1	F5	Balsa 10 mm
Servo hatch	1	F11	Plywood 1.2 mm
Fuselage Former	1	F6	Plywood 3 mm
Fuselage Formers	1+1+1	F4+F8+F10	Lite Ply 3 mm
Fuselage cross-brace	1+1	F17+F18	Lite Ply 3 mm
Fuselage hatch lock	1	F14	Lite Ply 3 mm
Tail boom fairing ring	2	F21	Lite Ply 3 mm
Wing riblet	1	W2	Lite Ply 3 mm
Root rib dihedral jig	1		Lite Ply 3 mm
Nose Shape Template	1		Lite Ply 3 mm
Bag no. 3
Wing rib	2	W6	Plywood 0.8 mm
Wing centre sheeting reinforcement	2	W54	Plywood 0.8 mm
Wing joiner bay plate	4	W43	Plywood 0.8 mm
Towhook plate	1	F7	Plywood 2 mm
Wing captive nut brace	1	F9	Plywood 2 mm
Wing bolt plate	1	W59	Plywood 2 mm
Wing tip spar	2	W38	Plywood 2 mm
Wing riblet	1	W1	Lite Ply 3 mm
Wing joiner	1	W42	Lite Ply 3 mm
Wing tip reinforcement plate	2	W39	Lite Ply 1.5 mm
Bag no. 4 - tail
Horizontal stabilizer	1	T1	Balsa 2.5 mm
Elevator	1	T2	Balsa 2.5 mm
Horizontal stabilizer reinforcement plate	1	T3	Balsa 2.5 mm
Fin	1	R1	Balsa 2.5 mm
Rudder	1	R2	Balsa 2.5 mm
Carbon fin reinforcement	1	R3	Carbon strip 0.5×3 mm
Tailplane pylon	1	F22
Bag no. 5
Wing rib	2	W6,8,10,12,14,16,18,20,22,24,26,28	Balsa 1.5 mm
Wing riblet	2	W7,9,11,13,15,17,19,21,23,25,27,29,31	Balsa 1.5 mm
Wing root rib	2	W3	Balsa 4 mm
Wing tip rib	2+2	W30, W32	Balsa 4 mm
Wing rib	2+2	W4, W10	Balsa 3 mm
Trailing edge	1+1	W44, W45	Balsa 3×15 mm
Leading edge	2	W46	Beech dowel Ø3 mm
Wing tip reinforcement (bottom)	2+2	W36,W37	Balsa 4 mm
Wing tip reinforcement (top)	2+2	W40, W41	Balsa 4 mm
Wing tip	2	W35	Balsa 1.5 mm
Gusset	4	W49	Balsa 1.5 mm
Wing main spar	2	W60	Carbon tube Ø6/5 mm
Auxiliary spar	2	W61	Carbon tube Ø3 mm
Rear spar	2	W647	Balsa 4 mm
Aileron leading edge	2	W48	Balsa 4 mm
Aileron root/tip rib	2+2	W62, W63	Balsa 4 mm
Aileron servo frame	2	W51	Balsa 4 mm
Aileron servo top cover plate	2	W52	Balsa 1.5 mm
Aileron servo bottom cover plate	2	W53	Balsa 1.5 mm
Aileron horn block	2	W50	Balsa 4 mm
Wing centre sheeting	2+2+2+2	W55, W56, W57, W58	Balsa 1.5 mm
Bag no. 6
Fuselage side	1+1	F2L/R	Balsa 1.5 mm
Fuselage bottom sheeting	1	F16	Balsa 2.5 mm
Fuselage upper sheeting	1+1+1	F13a, b, c	Balsa 2.5 mm
Fuselage side reinforcement plate	1+1	F2L/R	Balsa 3 mm
Tail boom fairing	1+1	F19, F20	Balsa 2.5 mm